Textronic Sensors of Hazardous Gaseous Substances.

Toxic materials are a threat in workplaces and the environment, as well as households. In them, gaseous substances are included, especially ones without any colour or fragrance, due to their non-detectability with the human senses. In this article, an attempt was made to find a solution for its detection in various conditions with the use of intelligent textiles.

Evaluation of the Thermal Insulation Properties of Composites with ZrO/Al Coatings Intended for the Construction of Protective Gloves.

The article presents research on the evaluation of the use of two four-layer textile composites with ZrO/Al coatings of different thicknesses (deposited by magnetron sputtering PVD) with potential use in thermally insulating protective gloves designed for steelworkers, welders, or miners. The structure of the composites was analyzed using high-resolution X-ray micro-CT. The assessment of the safety of the glove user was conducted using methods in which the composites were exposed to contact heat, radiant heat, and flame heat.

Ecological Repellent Preparations Based on Natural Polymers with the Addition of Essential Oils Acting on Ticks.

Background: Ticks (Acari: Ixodida) pose a serious medical and veterinary threat as vectors of tick-borne pathogens. The wide variety of tick repellents available on the market primarily consist of synthetic preparations that may disrupt the ecological balance and accumulate in the environment, leading to harmful effects on humans and animals. The aim of the study was to develop an ecological preparation based on natural raw materials (biopolymers) with the addition of a mixture of essential oils that act as tick repellents.

Modulating π-bridge in donor-π-acceptor covalent organic frameworks for low-energy-light-driven photocatalytic reaction.

Most of the photocatalytic reactions are currently driven by high-energy light (UV, blue light), which inevitably leads to side reactions and co-catalyst deactivation. Therefore, there is an urgent need to prepare novel photocatalysts with low-energy photocatalytic properties. Herein, we report a rational molecular design of covalent organic frameworks (COFs) equipped with donor-π-acceptor systems with different π-bridges (aromatic ring, mono- and bis-alkynyl).

Covalent Organic Frameworks with Tunable Bridge Positions for Photocatalytic CO Reduction to Propylene Under Visible Light Illumination.

The use of sunlight to convert CO into multi-carbon fuels, particularly propylene, is considered a sustainable carbon cycle pathway, but propylene requires a multi-electron-coupled proton reaction process that has not been reported. Herein, two covalent organic frameworks (DA-COF and DP-COF) are prepared by varying the bridging positions of anthraquinone conjugated units. The experimental results show that the neighbouring bridge in DA-COF forms a unique cleavage structure like an enzyme catalyst, which can provide an efficient microenvironment for the reduction reaction to trap protons.

Near infrared laser precisely controlled ultrafast superhydrophilicity-to-hydrophobicity transition of copper sulfide nanosphere coating on cellulose fiber fabric.

Inspired by lotus leaf, biomimetic hydrophobic cellulose fiber-based textiles were usually fabricated by the lower surface energy materials. However, it is rare to witness a hydrophobic surface obtained by near infrared laser (NIR) irradiation a superhydrophilic nanomaterial, which remains a huge challenge. Herein, the CuS nanospheres was in-situ anchored on the surface of gallic acid self-polymer treated cotton fabric.

A New Approach to Implementing 3D-Printed Material Structures for Protective Gloves with the Use of Ultrasonic and Contact Welding Processes: A Preliminary Study.

This study presents a new approach to developing protective material structures for personal protective equipment (PPE), and in particular for protective gloves, with the use of ultrasonic and contact welding processes. The goal was to assess the quality of joints (welds) obtained between a synthetic polyamide knitted fabric (PA) and selected polymers (PLA, ABS, PET-G) in the developed materials using X-Ray microtomography (micro-CT). Quantitative and qualitative analyses were performed to determine the joint area produced by the selected welding methods for the examined materials.

Comparative Evaluation of Bone-Implant Contact in Various Surface-Treated Dental Implants Using High-Resolution Micro-CT in Rabbits' Bone.

This study evaluated the bone-to-implant contact (BIC) of various surface-treated dental implants using high-resolution micro-CT in rabbit bone, focusing on the effects of different treatments on osseointegration and implant stability before and after bone demineralization. Six male New Zealand White rabbits were used. Four implant types were tested: machined surface with anodizing, only etching, sandblasting with AlO + etching, and sandblasting with TiO + etching.

Directionally Oriented Reinforcements of Warp-Knitted Fabrics for Composite Preforms.

This paper focuses on the development of a methodology for the directional structural modification of warp-knitted fabrics by sewing on carbon fiber tapes. Four-, five-, and six-axial geometric systems were designed to optimize the qualitative distribution of stresses on the surface of the tested product. Through a numerical experiment in the ANSYS environment, the impact of the change in the axiality of a textile structure on the mechanical properties of the modeled geometric configuration was assessed.

The Influence of Diatomite on the Sound Absorption Ability of Composites.

Diatomites are well-known mineral materials formed thousands of years ago from the skeletons of diatoms. They are found in many places around the world and have a wide range of applications. This article presents innovative research related to the possibility of using diatomite as a filler in composites to improve their sound absorption properties.

Assessing the Impact of Drought Stress on Hemp ( L.) Fibers.

Drought can significantly impact fiber crop cultivation due to the plants' specific water requirements and their extended vegetative period. The purpose of the research was to examine how drought stress affects the quality and chemical composition of hemp ( L.) fibers.

Biolaminates as an Example of Upcycling Product with Keratin Flour-Research and Thermal Properties Modeling.

Keratin waste, including keratin powder, is a significant byproduct of the poultry processing and meat industries. It is a major contributor to waste management problems due to its volume and the environmental pollutants that it can produce. The disposal of keratin waste is challenging due to the potential for odors and pathogens to enter the soil and water.

Evaluation of the Impact of Parylene C Deposition Method on the Functional Properties of Fabrics.

The article presents the results of research on the impact of the use of an original, innovative method of deposition of Parylene C on the functional properties of fabrics with various potential applications (e.g., thermal and chemical protective clothing, packaging, covers and others).

Modern Electromagnetic-Radiation-Shielding Materials Made Using Different Knitting Techniques.

This paper summarizes the possibility of employing knitted textile barriers as a shield against electromagnetic fields to protect the human body from their negative impact. Ten variants of knitted fabrics made of electrically conductive yarns, steel, and copper wire that differed in stitch pattern, structural parameters, and raw material, were designed, manufactured, and tested. The knitted fabrics produced differed in structural parameters, including course and wale density, surface density, thickness, thread length in the loop, wale and course take-up, volume cover factor, and surface porosity.

The Use of Various Types of Waste Paper for the Removal of Anionic and Cationic Dyes from Aqueous Solutions.

This study examined the possibility of using various types of waste paper-used newsprint (NP), used lightweight coated paper (LWC), used office paper (OP), and used corrugated cardboard (CC)-for the removal of anionic dyes, Acid Red 18 (AR18) and Acid Yellow 23 (AY23), and cationic dyes, Basic Violet 10 (BV10) and Basic Red 46 (BR46), from aqueous solutions. The scope of this research included the characterization of sorbents (FTIR, SEM, BET surface area, porosity, pH, effectiveness of water coloration), determination of pH effect on the effectiveness of dye sorption, sorption kinetics (pseudo-first-order model, second-order model, intraparticular diffusion model), and the maximum sorption capacity (Langmuir models and Freundlich model) of the tested sorbents. The use of waste paper materials as sorbents was found to not pose any severe risk of aquatic environment contamination.

Assessment of the Influence of Fabric Structure on Their Electro-Conductive Properties.

Electro-conductive fabrics are key materials for designing and developing wearable smart textiles. The properties of textile materials depend on the production method, the technique which leads to high conductivity, and the structure. The aim of the research work was to determine the factors affecting the electrical conductivity of woven fabrics and elucidate the mechanism of electric current conduction through this complex, aperiodic textile material.

Synthesis, molecular modelling, and antibacterial evaluation of new sulfonamide-dyes based pyrrole compounds.

In this study, we synthesized new series of 5-oxo-2-phenyl-4-(arylsulfamoyl)sulphenyl) hydrazono)-4,5-dihydro-1H-pyrrole-3-carboxylate hybrids 4a-f with the goal of overcoming sulfonamide resistance and identifying novel therapeutic candidates by chemical changes. The chemical structures of the synthesized hybrids were established over the spectroscopic tools. The frontier molecular orbitals configuration and energetic possessions of the synthesized compounds were discovered utilizing DFT/B3LYP/6-311++ G** procedure.

Internal Adaptation of Composite Fillings Made Using Universal Adhesives-A Micro-Computed Tomography Analysis.

This study aimed to evaluate internal tooth-filling interfaces of composite fillings made using universal adhesives using micro-computed tomography (µCT). Sixty class V cavities were randomly assigned into six groups: Peak Universal etch and rinse (PER), Peak Universal self-etch (PSE), Adhese Universal etch and rinse (AER), and Adhese Universal self-etch (ASE). Two further adhesives considered gold standards were used as control groups: OptiBond FL (OER) for the etch and rinse technique and Clearfil SE for the self-etch technique (CSE).

Influence of Low-Molecular-Weight Esters on Melt Spinning and Structure of Poly(lactic acid) Fibers.

Poly(lactic acid) has great potential in sectors where degradability is an important advantage due to its polymer nature. The medical, pharmaceutical, and packaging industries have shown interest in using PLA. To overcome the limitations of stiffness and brittleness in the polymer, researchers have conducted numerous modifications to develop fibers with improved properties.

Assessment of Impact of the Surface Modification Techniques on Structural, Biophysical, and Electrically Conductive Properties of Different Fabrics.

This article presents studies on the evaluation of the impact of surface modification of cotton, viscose, and polyester fabrics using three techniques (flocking, layer by layer, and screen printing) with materials with electrically conductive properties on their structural, biophysical, and conductive properties. Each tested fabric is characterized by specific biophysical properties. which can be disturbed by various modification methods, therefore, the following tests were carried out in the article: optical microscopy, micro-computed tomography, guarded perspiration heating plate, air permeability, sorption and electrical conductivity tester.

Investigation of the Hydrolytic Degradation Kinetics of 3D-Printed PLA Structures under a Thermally Accelerated Regime.

The application of biobased and biodegradable polymers, such as polylactide (PLA), in fused deposition modeling (FDM) 3D-printing technology creates a new prospect for rapid prototyping and other applications in the context of ecology. The popularity of the FDM method and its significance in material engineering not only creates new prospects for the development of technical sciences on an industrial scale, but also introduces new technologies into households. In this study, the kinetics of the hydrolytic degradation of samples obtained by the FDM method from commercially available PLA filaments under a thermally accelerated regime were analyzed.

Incorporating Antimicrobial Activity During Synthesis of New Acid-Azo Dyes: Thermal Stability and Application on Various Fabrics.

Background: Textile materials are susceptible to microbial attack as they provide suitable conditions for their growth. The microbes grow with normal body secretions on garments. These microbes are responsible for the weakening, brittleness, and discoloration of the substrate.

Correction: Zhu et al. Biodegradable and pH Sensitive Peptide Based Hydrogel as Controlled Release System for Antibacterial Wound Dressing Application. 2018, , 3383.

During the course of a review of our publication, we found two errors in Figure 4b and Figure 9 [...

Hedgehog artificial macrophage with atomic-catalytic centers to combat Drug-resistant bacteria.

Pathogenic drug-resistant bacteria represent a threat to human health, for instance, the methicillin-resistant Staphylococcus aureus (MRSA). There is an ever-growing need to develop non-antibiotic strategies to fight bacteria without triggering drug resistance. Here, we design a hedgehog artificial macrophage with atomic-catalytic centers to combat MRSA by mimicking the "capture and killing" process of macrophages.

Preparation and Performance Evaluation of Antibacterial Melt-Spun Polyurethane Fiber Loaded with Berberine Hydrochloride.

(1) Background: Bacterial infections have long threatened global public safety; hence, it is significant to continuously develop antibacterial fibers that are closely related to people's daily lives. Berberine hydrochloride is a natural antibacterial agent that has application prospects in the preparation of antibacterial fibers. (2) Methods: This study firstly verified the antibacterial properties of berberine hydrochloride and its possible antibacterial mechanism.