Processing follows function: pushing the formation of self-assembled monolayers to high-throughput compatible time scales.

Self-assembled monolayers (SAMs) of organic molecules can be used to tune interface energetics and thereby improve charge carrier injection at metal-semiconductor contacts. We investigate the compatibility of SAM formation with high-throughput processing techniques. Therefore, we examine the quality of SAMs, in terms of work function shift and chemical composition as measured with photoelectron and infrared spectroscopy and in dependency on molecular exposure during SAM formation.

Lateral ordering of PTCDA on the clean and the oxygen pre-covered Cu(100) surface investigated by scanning tunneling microscopy and low energy electron diffraction.

We have investigated the adsorption of perylene-3,4,9,10-tetracarboxylic acid dianhydride (PTCDA) on the clean and on the oxygen pre-covered Cu(100) surface [referred to as (√2 × 2√2)R45° - 2O/Cu(100)] by scanning tunneling microscopy (STM) and low energy electron diffraction (LEED). Our results confirm the (4√2 × 5√2)R45° superstructure of PTCDA/Cu(100) reported by A. Schmidt et al.

Eco-friendly fabrication of 4% efficient organic solar cells from surfactant-free P3HT:ICBA nanoparticle dispersions.

Photo-active layers from non-stabilized P3HT:ICBA nanoparticles enable the fabrication of inverted organic solar cells from eco-friendly, alcoholic dispersions. Exhibiting power conversion efficiencies (PCEs) ≈4%, the devices are competitive to state-of-the-art P3HT:ICBA solar cells from chlorinated solvents. Upon thermal annealing, the short circuit current density and consequently the PCE of the inverted solar cells improve radically due to a more intimate contact of the nanoparticles and hence an enhanced charge carrier extraction.

Printing PPEs: Fundamental Structure-Property Relationships.

A series of differentially alkyl- and alkoxy-substituted poly(-pheneyleneethynylene)s of different molecular weight were prepared and their rheological properties investigated. It was found that the side chain structure of the PPEs of roughly equal molecular weight and degree of polymerization has a significant influence on the rheology and printing behavior of the PPEs. Introduction of branched alkoxy or alkyl substituents improve the printing behavior of the PPEs dramatically.

Sensitivity improvement in fluorescence-based particle detection.

Microfluidic flow cytometers are highly interesting candidates for biomedical point-of-care applications. However, the sensitivity, reliability, and throughput of these systems must be improved to provide the full functionality of established flow cytometric systems. One proposed method to improve fluorescence detection systems is to use spatial modulation techniques.

Solution processed, white emitting tandem organic light-emitting diodes with inverted device architecture.

Fully solution processed monochromatic and white-light emitting tandem or multi-photon polymer OLEDs with an inverted device architecture have been realized by employing WO3 /PEDOT:PSS/ZnO/PEI charge carrier generation layers. The luminance of the sub-OLEDs adds up in the stacked device indicating multi-photon emission. The white OLEDs exhibit a CRI of 75.

Cell-penetrating peptoids: introduction of novel cationic side chains.

During the last decade peptoid-based molecular transporters have been broadly applied. They are highly valued for their easy synthesis and their superior stability against enzymatic degradation. The special structure of peptoids generally allows introducing a variety of different side chains.

Investigation of solution-processed ultrathin electron injection layers for organic light-emitting diodes.

We study two types of water/alcohol-soluble aliphatic amines, polyethylenimine (PEI) and polyethylenimine-ethoxylated (PEIE), for their suitability as electron injection layers in solution-processed blue fluorescent organic light-emitting diodes (OLEDs). X-ray photoelectron spectroscopy is used to determine the nominal thickness of the polymer layers while ultraviolet photoelectron spectroscopy is carried out to determine the induced work-function change of the silver cathode. The determined work-function shifts are as high as 1.

Enhanced electron injection into inverted polymer light-emitting diodes by combined solution-processed zinc oxide/polyethylenimine interlayers.

Inverted device architectures for organic light-emitting diodes (OLEDs) require suitable interfaces or buffer layers to enhance electron injection from highwork-function transparent electrodes. A solution-processable combination of ZnO and PEI is reported, that facilitates electron injection and enables efficient and air-stable inverted devices. Replacing the metal anode by highly conductive polymers enables transparent OLEDs.

The compromises of printing organic electronics: a case study of gravure-printed light-emitting electrochemical cells.

Light-emitting electrochemical cells (LECs) are fabricated by gravure printing. The compromise between device performance and printing quality is correlated to the ink formulation and the printing process. It is shown that the rheological properties of the ink formulations of LECs can be tailored without changing the chemical composition of the material blend.

looking inside a working SiLED.

In this study, we investigate for the first time morphological and compositional changes of silicon quantum dot (SiQD) light-emitting diodes (SiLEDs) upon device operation. By means of advanced transmission electron microscopy (TEM) analysis including energy filtered TEM (EFTEM) and energy dispersive X-ray (EDX) spectroscopy, we observe drastic morphological changes and degradation for SiLEDs operated under high applied voltage ultimately leading to device failure. However, SiLEDs built from size-separated SiQDs operating under normal conditions show no morphological and compositional changes and the biexponential loss in electroluminescence seems to be correlated to chemical and physical degradation of the SiQDs.

Tungsten oxide buffer layers fabricated in an inert sol-gel process at room-temperature for blue organic light-emitting diodes.

WO3 deposition from tungsten ethoxide precursor solutions at room temperature is demonstrated. The W(OEt)6 precursor can be converted under inert conditions and hence avoids sample contamination with oxygen, opening a pathway to more stable devices. The stoichiometry of all WO3 layers and the optoelectronic performance of the respective SMOLEDs well match thermally evaporated WO3 and its corresponding SMOLEDs.

Linear and nonlinear optical characterization of aluminum nanoantennas.

We experimentally determine the order of multiphoton induced luminescence of aluminum nanoantennas fabricated on a nonconductive substrate using electron-beam lithography to be 2.11 (±0.10).

Investigating the influences of the precise manufactured shape of dipole nanoantennas on their optical properties.

Fabrication of small nanoantennas with high aspect ratios via electron beam lithography is at the current technical limit of nanofabrication and hence significant deviations from the intended shape of small nanobars occur. Via numerical simulations, we investigate the influence of geometrical variations of gap nanoantennas, having dimensions on the order of only a few tens of nanometers. We show that those deviations have a significant influence on the performance of such nanoantennas.

White organic light emitting diodes with enhanced internal and external outcoupling for ultra-efficient light extraction and Lambertian emission.

White organic light emitting diodes (WOLEDs) suffer from poor outcoupling efficiencies. The use of Bragg-gratings to enhance the outcoupling efficiency is very promising for light extraction in OLEDs, but such periodic structures can lead to angular or spectral dependencies in the devices. Here we present a method which combines highly efficient outcoupling by a TiO(2)-Bragg-grating leading to a 104% efficiency enhancement and an additional high quality microlens diffusor at the substrate/air interface.

Multicolor silicon light-emitting diodes (SiLEDs).

We present highly efficient electroluminescent devices using size-separated silicon nanocrystals (ncSi) as light emitting material. The emission color can be tuned from the deep red down to the yellow-orange spectral region by using very monodisperse size-separated nanoparticles. High external quantum efficiencies up to 1.

Direct fabrication of PDMS waveguides via low-cost DUV irradiation for optical sensing.

We demonstrate the fabrication of single mode optical waveguides by irradiating polydimethylsiloxane (PDMS) with a low cost Hg lamp through a conventional quartz mask. By increasing the refractive index of the irradiated areas, waveguiding is achieved with an attenuation of 0.47 dB/cm at a wavelength of 635 nm.

White organic light emitting diodes with enhanced internal and external outcoupling for ultra-efficient light extraction and Lambertian emission.

White organic light emitting diodes (WOLEDs) suffer from poor outcoupling efficiencies. The use of Bragg-gratings to enhance the outcoupling efficiency is very promising for light extraction in OLEDs, but such periodic structures can lead to angular or spectral dependencies in the devices. Here we present a method which combines highly efficient outcoupling by a TiO(2)-Bragg-grating leading to a 104% efficiency enhancement and an additional high quality microlens diffusor at the substrate/air interface.

Continuously tunable solution-processed organic semiconductor DFB lasers pumped by laser diode.

The fabrication and characterization of continuously tunable, solution-processed distributed feedback (DFB) lasers in the visible regime is reported. Continuous thin film thickness gradients were achieved by means of horizontal dipping of several conjugated polymer and blended small molecule solutions on cm-scale surface gratings of different periods. We report optically pumped continuously tunable laser emission of 13 nm in the blue, 16 nm in the green and 19 nm in the red spectral region on a single chip respectively.

Efficient waveguide mode extraction in white organic light emitting diodes using ITO-anodes with integrated MgF₂-columns.

We report a simple approach to enhance the out-coupling efficiency in white organic light emitting diodes (WOLEDs). By incorporating MgF₂-columns into the ITO-anode and optimizing of their geometry, an overall efficiency enhancement of up to 38% is achieved. In addition, the structuring of the anode does not lead to a change in the electrical behaviour of the devices.

Flexible planar microfluidic chip employing a light emitting diode and a PIN-photodiode for portable flow cytometers.

Detection of fluorescence particles is a key method of flow cytometry. We evaluate the performance of a design for a microfluidic fluorescence particle detection device. Due to the planar design with low layer thicknesses, we avoid optical components such as lenses or dichroic mirrors and substitute them with a shadow mask and colored film filters.

On the interplay of waveguide modes and leaky modes in corrugated OLEDs.

Bragg gratings incorporated into organic light-emitting diodes (OLEDs) establish a coupling between waveguide modes and useful light (leaky modes). Here we demonstrate that the net coupling direction depends on the OLED stack design. We fabricated two different device structures with gold Bragg gratings.

Improving the outcoupling efficiency of indium-tin-oxide-free organic light-emitting diodes via rough internal interfaces.

We present low-cost texturing methods to produce different surface roughnesses on glass substrates. Using sand blasting, abrasion and wet etching we achieve roughnesses of about 50 nm to 250 nm (root mean squared roughness Rq). These textured substrates are used as extraction elements for guided modes and substrate modes in organic light-emitting diodes (OLEDs).

Intermediate high index layer for laser mode tuning in organic semiconductor lasers.

We modified the optical properties of organic semiconductor distributed feedback lasers by introducing a high refractive index layer consisting of tantalum pentoxide between the substrate and the active material layer. A thin film of tris-(8-hydroxyquinoline) aluminium doped with the laser dye 4-dicyanomethylene-2-methyl-6-(p-dimethylamino-styryl)-4H-pyran was used as the active layer. By varying the intermediate layer thickness we could change the effective refractive index of the guided laser mode and thus the laser wavelength.

Laser speckle reduction via colloidal-dispersion-filled projection screens.

We use projection screens filled with colloidal dispersions to reduce laser speckle in laser projection systems. Laser light is multiply scattered at the globules of the colloidal dispersion's internal phase, which do Brownian movement. The integration time of the human eye causes a perception of a reduced laser speckle contrast because of temporal averaging.