26 children with 29 lower limb fractures, between the age of 2 and 15 years, were treated with an external fixator. The average time to union and removal of the fixator was 71 days for femoral and 73 days for tibial fractures. Complications included pin problems in nine cases, two devices had to be replaced with a cast and one refracture. Leg length discrepancies were noted in five children and radiological malalignment in three. We recommend external fixation for all femoral shaft fractures and all open or dislocated tibial and tibia and fibula fractures beginning at the age of three to adolescence.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1055/s-2008-1071116 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Long bone fractures with associated vascular injury: Who should go first?
Injury
January 2025
Temple University Hospital, Department of Orthopaedic Surgery, USA.
Objectives: Long bone fractures with concomitant vascular injury have the potential to be life and limb threatening injuries, with increased risk for limb loss. There is currently no established surgical order of operations for orthopaedic and vascular intervention. This study compares injury classification, warm ischemia time and patient outcomes in patients with long bone fractures and associated vascular injury after orthopaedic versus vascular primary intervention.
View Article and Find Full Text PDFThe Risk of Postoperative Periprosthetic Femoral Fracture After Total Hip Arthroplasty Depends More on Stem Design Than Cement Use: An Analysis of National Health Data from England.
J Bone Joint Surg Am
January 2025
Leeds Institute of Health Sciences, School of Medicine, University of Leeds, Leeds, West Yorkshire, England.
Background: In this study, we estimated the risk of surgically treated postoperative periprosthetic femoral fractures (POPFFs) associated with femoral implants frequently used for total hip arthroplasty (THA).
Methods: In this cohort study of patients who underwent primary THA in England between January 1, 2004, and December 31, 2020, POPFFs were identified from prospectively collected revision records and national hospital records. POPFF incidence rates, adjusting for potential confounders, were estimated for common stems.
Revision quadriceps tendon repair: A case series and technique guide to a novel repair.
Trauma Case Rep
February 2025
Department of Orthopaedic Surgery and Sports Medicine, University at Buffalo, Jacobs School of Medicine and Biomedical Sciences, Buffalo, NY 14203, United States of America.
Introduction: Revision quadriceps tendon repair is a challenging problem. In this four-case series, novel quadriceps tendon revision resulted in improved range of motion and durable repair for patients with recurrent rupture.
Methods: Our technique includes a combination of a running locked #5 FiberWire or 2 mm SutureTape suture placed through parallel medial, lateral, and central drill holes in the patella with running Krackow-type quadriceps tendon repair medially and laterally resulting in four strands, delivering the vastus medialis and medial quadriceps tendon to an anatomic repair at the superior pole of the patella, with 2 sutures passed centrally and 1 each passed medially and laterally and then tied.
Medialization of shaft of humerus to provide medial buttress and prevent varus collapse in 3- and 4-part proximal humerus fractures: review of the surgical technique.
JSES Rev Rep Tech
February 2025
Department of Orthopaedics, Krishna Institute of Medical Sciences, Secunderabad, Telanagana, India.
Hypothesis: Proximal humerus fractures present a treatment challenge due to varied fracture configurations and a lack of consensus on optimal management. Locking plate designs offer promising solutions, yet technical guidelines for successful outcomes remain elusive. Complications are common, with fixation-related failures often attributed to varus collapse.
View Article and Find Full Text PDFAim: Fixed retention is the method of choice for permanent stabilization of the treatment outcome. In recent years, CAD/CAM techniques have been developed to produce retainers with high precision and tension-free fit. The aim of this retrospective study was to evaluate the suitability of a semi-industrial retainer manufacturing process (office-based construction, external laboratory manufacturing) in terms of positioning accuracy and post-treatment changes.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!