Perioperative thermal manipulations are usually directed at the skin surface because methods of directly warming the core are invasive or ineffective. However, inadequate heat flow between peripheral and core compartments will decrease the rate at which core temperature changes. We therefore determined whether core hypothermia is delayed after initiation of surface cooling. Six volunteers were anesthetized with propofol and midazolam, and maintained under three layers of passive insulation for 2.5-4 h. Subsequently, the skin surface was cooled using forced air, 1000 L/min, at 10 degrees C. Isoflurane was added as necessary to maintain arteriovenous shunt vasodilation. Overall heat balance was determined from the difference between cutaneous heat loss (thermal flux transducers) and metabolic heat production (oxygen consumption). Average arm and leg (peripheral) tissue temperatures were determined from 19 intramuscular needle thermocouples, 10 skin temperatures, and "deep" foot temperature. Overall body heat content decreased approximately 234 kcal during 2.5 h of active cooling. Core temperature, which was nearly constant before active cooling, decreased approximately 1.3 degrees C/h. There was no delay between initiation of active cooling and the decrease in core temperature. Furthermore, peripheral (arm and leg) and core (trunk and head) tissue heat contents decreased at virtually the same rates: approximately 50 kcal/h and approximately 47 kcal/h, respectively. These data indicate that there is little restriction of heat flow between peripheral and core tissues in vasodilated, anesthetized subjects.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1097/00000539-199605000-00006 | DOI Listing |
Biosens Bioelectron
January 2025
Key Laboratory of Laboratory Medical Diagnostics, Ministry of Education, Department of Laboratory Medicine, Chongqing Medical University, Chongqing, China. Electronic address:
Isothermal amplification-based nucleic acid detection technologies have become rapid and efficient tools for molecular diagnostics. Sequence-specific monitoring methods are crucial for isothermal amplification, as they help identify the occurrence of extended primer dimers, which can lead to false positive results. Fluorescent aptamers are promising tools for real-time monitoring of isothermal amplification but are inherently limited by thermostability.
View Article and Find Full Text PDFPharmaceutics
December 2024
Faculty of Pharmacy, University of Ljubljana, Aškerčeva Cesta 7, 1000 Ljubljana, Slovenia.
Background/objectives: Lactoferrin (Lf), a multifunctional iron-binding protein, has considerable potential for use as an active ingredient in food supplements due to its numerous positive effects on health. As Lf is prone to degradation, we aimed to develop a formulation that would ensure sufficient stability of Lf in the gastrointestinal tract and during product storage.
Methods: A simple, efficient, and well-established technology that has potential for industrial production was used for the double-coating of neutral pellet cores with an Lf layer and a protective enteric coating.
Polymers (Basel)
January 2025
Engineering Research Center of Oil and Gas Field Chemistry, Universities of Shaanxi Provence, Xi'an Shiyou University, Xi'an 710065, China.
In order to solve the problems of long dissolution and preparation time, cumbersome preparation, and easy moisture absorption and deterioration during storage or transportation, acrylamide (AM), acrylic acid (AA), sodium p-styrene sulfonate (SSS), and cetyl dimethylallyl ammonium chloride (DMAAC-16) were selected as raw materials, and the emulsion thickener P(AM/AA/SSS), which can be instantly dissolved in water and rapidly thickened, was prepared by the reversed-phase emulsion polymerization method. DMAAC-16, the influence of emulsifier dosage, oil-water ratio, monomer molar ratio, monomer dosage, aqueous pH, initiator dosage, reaction temperature, reaction time, and other factors on the experiment was explored by a single-factor experiment, and the optimal process was determined as follows: the oil-water volume ratio was 0.4, the emulsifier dosage was 7% of the oil phase mass, the initiator dosage was 0.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
Binzhou Institute of Technology, Weiqiao-UCAS Science and Technology Park, Binzhou 256606, China.
Due to the high viscosity and low fluidity of viscous crude oil, how to effectively recover spilled crude oil is still a major global challenge. Although solar thermal absorbers have made significant progress in accelerating oil recovery, its practical application is largely restricted by the variability of solar radiation intensity, which is influenced by external environmental factors. To address this issue, this study created a new composite fiber that not only possesses solar energy conversion and storage capabilities but also facilitates crude oil removal.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Soreq NRC, Yavne 81800, Israel.
Fiber Bragg gratings (FBGs) inscribed by UV light and different femtosecond laser techniques (phase mask, point-by-point, and plane-by-plane) were exposed-in several irradiation cycles-to accumulated high doses of gamma rays (up to 124 MGy) and neutron fluence (8.7 × 10/cm) in a research-grade nuclear reactor. The FBG peak wavelengths were measured continuously in order to monitor radiation-induced shifts.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!