With the advancement of ecological and environmental protection construction, the research on the modification of expansive soil using environmentally friendly polymers can make up for the harm to the ecological environment caused by traditional modification. Mechanical and microscopic properties of modified expansive soils were analyzed through indoor tests. The results showed that the liquid limit and plasticity index decreased by 52.14% and 77.36%, respectively, and the plastic limit increased by 20.83%. Maximum dry density decreased by 5.11% and optimum moisture content increased by 28.47%. The compressive and shear strength increases and then decreases with the increase of dosage, and the strength reaches the maximum when the dosage is 4%, and the vertical and lateral deformation of the specimen is the smallest. Modified soil swelling was reduced by 54.57% and swelling forces were reduced by 15-57%. The modified soil cracks developed slowly and the width of the cracks was reduced by 61.68% after the modification. Microscopy showed that no new minerals were generated after doping modifier, while hydrophilic minerals were reduced by 43.14%, and the gel film formed by hydration made the pores smaller and the structure tighter by filling and wrapping on the surface of the particles.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1038/s41598-025-85395-3 | DOI Listing |
Sci Rep
January 2025
School of Civil Engineering, Architecture and Environment, Hubei University of Technology, Wuhan, 430068, China.
With the advancement of ecological and environmental protection construction, the research on the modification of expansive soil using environmentally friendly polymers can make up for the harm to the ecological environment caused by traditional modification. Mechanical and microscopic properties of modified expansive soils were analyzed through indoor tests. The results showed that the liquid limit and plasticity index decreased by 52.
View Article and Find Full Text PDFSci Rep
January 2025
Faculty of Mechanical Engineering, VŠB -Technical University of Ostrava, 17. listopadu 2172/15, 708 00, Ostrava-Poruba, Czech Republic.
Three types of commercial austenitic stainless steels, 1.4307 (AISI 304 L), 1.4404 (AISI 316 L) 1.
View Article and Find Full Text PDFSci Rep
January 2025
Dazhu Coal and Electricity Group of Sichuan, Xiaohezui Coal Mine, Dazhou, 6635000, China.
This study investigates the bearing characteristics and damage evolution of regenerative rock masses formed under varying geological conditions through uniaxial loading tests, numerical simulations, and theoretical derivations. Regenerative rock mass samples with different water-cement ratios and cementing materials were prepared, and the mechanical behavior during the loading process was analyzed. The results indicate that the secondary damage process can be divided into three stages: pre-peak, weakening, and friction.
View Article and Find Full Text PDFPhys Med Biol
January 2025
North Carolina State University, Fitts Woolard Hall, Raleigh, North Carolina, 27695-7908, UNITED STATES.
Motivated by elastography that utilizes tissue mechanical properties as biomarkers for liver disease, with the eventual objective of quantitatively linking histopathology and bulk mechanical properties, we develop a micromechanical modeling approach to capture the effects of fat and collagen deposition in the liver. Specifically, we utilize computational homogenization to convert the microstructural changes in hepatic lobule to the effective viscoelastic modulus of the liver tissue, i.e.
View Article and Find Full Text PDFJ Prosthet Dent
January 2025
Undergraduate student, School of Mechanical Engineering, Shandong University of Technology, Zibo, PR China.
Statement Of Problem: Infrared radiation heating (IRH) technology has been innovatively applied to the annealing of selective laser melted (SLM) cobalt chromium (Co-Cr) frameworks. However, previous studies have not reported the effects of IRH on the warping deformation and mechanical properties of these frameworks.
Purpose: The purpose of this in vitro study was to investigate the effects of IRH on the warping deformation and mechanical properties of dental SLM Co-Cr alloy and to evaluate its potential applications in dental restorations.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!