This study assesses radiation doses in multi-slice computed tomography (CT) using epoxy resin and PMMA phantoms, focusing on the relationship between TAR (tissue air ratio) and kilovoltage peak (kVp). The research was conducted using a Hitachi Supria 16-slice CT scanner. An epoxy resin phantom was fabricated from commercially available materials, to simulate human tissue. The phantom contained four peripheral inserts and one central insert for dose measurement, with optically stimulated luminescent dosimeters positioned at various depths (2 to 10 cm). Monte Carlo simulations were executed using the Geant4 Application for Tomographic Emission toolkit (GATE) to model photon transport, with the x-ray spectrum generated using SpekPy software. A non-linear fitting model was developed to describe the TAR-kVp relationship across different depths for epoxy resin and PMMA. Results indicated that TAR values were higher at low depths (2 cm) and decreased with increasing depth, reflecting the x-ray beam's attenuation. For instance, at 80 kVp and 2 cm depth, the experimental TAR for PMMA was 1.102 ± 0.011, closely matching the MC simulation value of 1.110 ± 0.036, resulting in a small difference of 0.7%. At a depth of 10 cm, the experimental TAR for PMMA decreased to 0.245 ± 0.006, while the MC TAR was 0.248 ± 0.016, with a relative difference of 1.2%. Similar trends were observed for epoxy resin, where the experimental TAR ranged from 1.070 ± 0.014 at 2 cm to 0.235 ± 0.009 at 10 cm, while MC simulation values ranged from 1.080 ± 0.038 to 0.238 ± 0.017. Bland-Altman analysis confirmed these results, with mean differences of 0.008 for PMMA and 0.006 for epoxy resin, indicating high agreement between the experimental and simulated TAR values. This study highlights the importance of phantom material selection in dose assessment and the implications of TAR in dose correction within the context of diagnostic radiology.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s00411-024-01105-z | DOI Listing |
J Contemp Dent Pract
October 2024
College of Dentistry, Ajman University, Ajman P.O. Box 346, United Arab Emirates; Department of Endodontic, Faculty of Dentistry, Mansoura University, Egypt, Orcid: https://orcid.org/0000-0003-3391-5306.
Aim: This study aimed to investigate and compare the total and sectional bond strengths of three endodontic sealers when used with the single-cone obturation technique.
Materials And Methods: Forty-five human maxillary central incisors were prepared and divided into three groups according to the type of endodontic sealer: Group I (Gutta-percha/AH Plus Jet), group II (Gutta-percha/GuttaFlow 2), and group III (RealSeal/RealSeal SE). All canals were filled with the single-cone technique.
Aim: This study aimed to evaluate OccluSense's reliability against conventional articulating films in assessing static occlusion. The study also targets to identify possible limitations and influencing factors when using this device to asses static occlusion.
Materials And Methods: This experimental research utilized twenty epoxy resin typodont models representing various occlusal discrepancies.
Macromol Rapid Commun
January 2025
Department of Materials Science and Engineering, University of Utah, Salt Lake City, Utah, 84112, USA.
Fiber-reinforced composites (FRCs) possess a remarkable strength-to-weight ratio, making them ideal light-weighing alternative materials of metals used in automotive, aerospace, and outdoor equipment applications, but their recycling is challenging. Chemically recyclable thermoset polymers can enable fiber recovery and reuse; however, challenges remain in the separation and purification of depolymerized small molecules for efficient polymer recycling. To this end, a series of liquid resins for chemically recyclable polymer networks is designed based on phthalic anhydride, a widely produced and inexpensive chemical.
View Article and Find Full Text PDFMacromol Rapid Commun
January 2025
College of Chemical and Biological Engineering, Zhejiang University, Zhejiang Provincial Key Laboratory of Advanced Chemical Engineering Manufacture Technology, Hangzhou, 310027, China.
Critical issues such as leakage, degradation, and thermal response hysteresis have become the focus in the application of phase change materials (PCMs) in area such as thermal management of fabrics. The encapsulation of PCMs prepared as microcapsules using polysiloxanes, etc. as a component unit of crosslinking agents represents a highly promising avenue of research.
View Article and Find Full Text PDFInt J Biol Macromol
January 2025
Key Laboratory of Automobile Materials, Ministry of Education, and College of Materials Science and Engineering, Jilin University, Changchun 130025, China. Electronic address:
A new type of filler was added to epoxy resin to prepare a composite coating with excellent corrosion and weathering resistance. The simple synthesis process and nonpolluting raw materials of this filler contribute to the development of green chemistry. Specifically, lignin was encapsulated in mesoporous silica, the synergistic effect between the two resulted in the formation of lignin/mesoporous silica composite particles (MSN-L) with excellent ultraviolet (UV) resistance.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!