This study examines the electromagnetic properties of a composite material composed of iron pyrite (FeS) and epoxy resin, mixed in a 3:2 weight ratio to create a 10 cm cube. The research analyzes transmission and reflection coefficients and band gap parameters to determine its viability as an antenna substrate for electromagnetic wave applications. The composite displays a tunable band gap of 1.3 eV, enabling selective absorption and emission of electromagnetic radiation. The transmission coefficient achieved 90% throughout a frequency range of 1 GHz to 15 GHz, whilst the reflection coefficient was measured at 10%, significantly reducing reflecting losses. The epoxy resin binder was essential for preserving structural integrity and augmenting the dielectric characteristics of the composite, thereby raising transmission efficiency. UV-Vis spectroscopy showed an absorption value of 0.875% at the band gap, indicating efficient interaction with UV energy. The S21 transmission coefficient ranged from -10 dB to -80 dB, with a maximum of -40 dB at 6 GHz, indicating strong energy transfer capability for antenna applications. The S21 values exhibited negligible signal attenuation between 2 GHz and 7 GHz, indicating the material's exceptional suitability for antenna substrates necessitating dependable transmission. The S11 reflection coefficient varied from -5 dB to -55 dB, with substantial decreases between 4 GHz and 14 GHz, when reflection decreased to -45 dB, signifying little signal reflection at essential frequencies. The results underscore the composite's appropriateness for applications requiring high transmission efficiency, little reflection, and effective engagement with electromagnetic waves, especially as an antenna substrate. Measurements were performed using a vector network analyzer (VNA) to obtain the S11 and S21 characteristics, underscoring the material's potential in sophisticated electromagnetic applications.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11595895 | PMC |
| http://dx.doi.org/10.3390/ma17225456 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Investigations on the Origin of Topotactic Phase Transition of LaCoO Thin Films with In Situ XRD and Ambient Pressure Hard X-ray Photoelectron Spectroscopy.
ACS Appl Mater Interfaces
December 2024
Department of Materials Science and Engineering, Chosun University, Gwangju 61452, Korea.
With the applications of in situ X-ray diffraction (XRD), electrical - measurement, and ambient pressure hard X-ray photoelectron spectroscopy (AP-HAXPES), the characteristics of the topotactic phase transition of LaCoO (LCO) thin films are examined. XRD measurements show clear evidence of structural phase transition (SPT) of the LCO thin films from the perovskite (PV) LaCoO to the brownmillerite (BM) LaCoO phases through the intermediate LaCoO phase at a temperature of 350 °C under high-vacuum conditions, ∼10 mbar. The reverse SPT from BM to PV phases is also found under ambient pressure (>100 mbar) of air near 100 °C.
View Article and Find Full Text PDFEngineering n-Type and p-Type BiOI Nanosheets: Influence of Mannitol on Semiconductor Behavior and Photocatalytic Activity.
Nanomaterials (Basel)
December 2024
School of Materials Science and Engineering, Changchun University of Science and Technology, Changchun 130022, China.
Photocatalytic technology holds significant promise for sustainable development and environmental protection due to its ability to utilize renewable energy sources and degrade pollutants efficiently. In this study, BiOI nanosheets (NSs) were synthesized using a simple water bath method with varying amounts of mannitol and reaction temperatures to investigate their structural, morphological, photoelectronic, and photocatalytic properties. Notably, the introduction of mannitol played a critical role in inducing a transition in BiOI from an n-type to a p-type semiconductor, as evidenced by Mott-Schottky (M-S) and band structure analyses.
View Article and Find Full Text PDFStudy on Electrical and Temperature Characteristics of β-GaO-Based Diodes Controlled by Varying Anode Work Function.
Nanomaterials (Basel)
December 2024
State Key Laboratory of Wide Bandgap Semiconductor Devices and Integrated Technology, National Engineering Research Center of Wide Band-Gap Semiconductor, School of Microelectronics, Xidian University, Xi'an 710071, China.
This study systematically investigates the effects of anode metals (Ti/Au and Ni/Au) with different work functions on the electrical and temperature characteristics of β-GaO-based Schottky barrier diodes (SBDs), junction barrier Schottky diodes (JBSDs) and P-N diodes (PNDs), utilizing Silvaco TCAD simulation software, device fabrication and comparative analysis. From the perspective of transport characteristics, it is observed that the SBD exhibits a lower turn-on voltage and a higher current density. Notably, the V of the Ti/Au anode SBD is merely 0.
View Article and Find Full Text PDFPlatinum Compound on Gold-Magnesia Hybrid Structure: A Theoretical Investigation on Adsorption, Hydrolysis, and Interaction with DNA Purine Bases.
Nanomaterials (Basel)
December 2024
Department of Chemistry and Chemical Engineering, Taiyuan Institute of Technology, Taiyuan 030008, China.
Cisplatin-based platinum compounds are important clinical chemotherapeutic agents that participate in most tumor chemotherapy regimens. Through density-functional theory calculations, the formation and stability of the inorganic oxide carrier, the mechanisms of the hydrolysis reaction of the activated platinum compound, and its binding mechanism with DNA bases can be studied. The higher the oxidation state of Pt (II to IV), the more electrons transfer from the magnesia-gold composite material to the platinum compound.
View Article and Find Full Text PDFBimetallic Mesoporous MCM-41 Nanoparticles with Ta/(Ti, V, Co, Nb) with Catalytic and Photocatalytic Properties.
Nanomaterials (Basel)
December 2024
Institute of Physical Chemistry-Ilie Murgulescu of the Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest, Romania.
Bimetallic (Ta/Ti, V, Co, Nb) mesoporous MCM-41 nanoparticles were obtained by direct synthesis and hydrothermal treatment. The obtained mesoporous materials were characterized by XRD, XRF, N adsorption/desorption, SEM, TEM, XPS, Raman, UV-Vis, and PL spectroscopy. A more significant effect was observed on the mesoporous structure, typically for MCM-41, and on optic properties if the second metal (Ti, Co) did not belong to the same Vb group with Ta as V and Nb.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!