The clinical success of laminate veneers depends upon their marginal discrepancy (MD) and internal gap (IG). This study aims to compare and evaluate the MD, overall discrepancy (OD), absolute marginal discrepancy (AMD), and IG of 3D-printed (Varseosmile TrinQ and Varseosmile Crown Plus) and computer-aided design and manufacturing (CAD/CAM)-milled (Brilliant Crios) laminate veneers using cone-beam computed tomography (CBCT). Thirty maxillary central incisors were prepared and divided randomly into three groups ( = 10). All teeth were scanned for veneer fabrication: Group PVT teeth with 3D-printed Varseosmile TrinQ, Group PVC teeth with 3D-printed Varseosmile Crown Plus, and Group BCM teeth with Brilliant Crios milled veneers. The specimens with respective veneers were scanned using CBCT, and the sectional images were measured for IG, MD, OD, and AMD. The mean values for MD recorded were 0.27, 0.31, and 0.40 for PVT, PVC, and BCM respectively). The mean values for IG recorded were as follows: PVT group-0.24, PVC group-0.28, and BCM group-0.39, and those for OD were as follows: PVT-0.22, PVC-0.32, and BCM-0.41. Intragroup significance was observed for IG and OD ( = 0.001). Findings revealed that milled veneers have a higher IG and MD than 3D-printed veneers, making them less clinically acceptable.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11595794 | PMC |
| http://dx.doi.org/10.3390/jfb15110338 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effect of crystallization and finish line curvature on the marginal integrity of lithium disilicate crowns.
J Prosthodont
January 2025
Department of Prosthodontics and Research Institute of Oral Science, College of Dentistry, Gangneung-Wonju National University, Gangneung, South Korea.
Purpose: This study aimed to investigate the effect of crystallization and finish line curvature on the integrity of lithium disilicate crowns fabricated by using partially crystallized (P) and fully crystallized (F) blocks.
Materials And Methods: Forty-eight lithium disilicate crowns were fabricated based on the designated lithium disilicate blocks and finish line curvatures. The specimens were divided into four groups (n = 12 each): P block with a curved finish line (PC), P block with a straight finish line (PS), F block with a curved finish line (FC), and F block with a straight finish line (FS).
The abiologically and biologically driving effects on organic matter in marginal seas revealed by deep learning-assisted model analysis.
Sci Total Environ
January 2025
Key Laboratory of Coastal Biology and Biological Resource Utilization, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003, China; University of Chinese Academy of Sciences, Beijing 101408, China. Electronic address:
The biogeochemical processes of organic matter exhibit notable variability and unpredictability in marginal seas. In this study, the abiologically and biologically driving effects on particulate organic matter (POM) and dissolved organic matter (DOM) were investigated in the Yellow Sea and Bohai Sea of China, by introducing the cutting-edge network inference tool of deep learning. The concentration of particulate organic carbon (POC) was determined to characterize the status of POM, and the fractions and fluorescent properties of DOM were identified through 3D excitation-emission-matrix spectra (3D-EEM) combined parallel factor analysis (PARAFAC).
View Article and Find Full Text PDFEvaluation of marginal accuracy of polyetheretherketone and zirconia copings fabricated using computer-aided design/computer-aided manufacturing technique: An in vitro study.
J Indian Prosthodont Soc
January 2025
Department of Prosthodontics, Chhattisgarh Dental College and Hospital, Rajnandgaon, Chhattishgarh, India.
Aim: The aim of this study was to compare the marginal accuracy of polyetheretherketone (PEEK) and zirconia copings fabricated using computer-aided design/computer-aided manufacturing (CAD/CAM) technology, and to assess the impact of their material properties on accuracy when produced with a 4-axis milling system under controlled conditions.
Settings And Design: The study employed an in vitro design with a stainless steel die model featuring a 6 mm axial wall height, a 6-degree total occlusal convergence, and a radial shoulder finish line.
Materials And Methods: Thirty stone dies were created from silicone impressions of the metal die and poured using type-IV dental stone.
Comparative evaluation of marginal fit accuracy of two different designs of endocrown manufactured through CAD-CAM system: An in vitro study.
J Indian Prosthodont Soc
January 2025
Department of Epidemiology, College of Medicine, University of Cincinnati, Ohio, USA.
Aims: To compare the accuracy of marginal fit of CAD-CAM endocrown with two different preparation forms, i.e., endocrown with ferrule and endocrown without ferrule.
View Article and Find Full Text PDFComparison of marginal fit between milled and three-dimensional printed polymethylmethacrylate prostheses for single crowns, anterior bridges, and pier abutment bridges: An in vitro study.
J Indian Prosthodont Soc
January 2025
Department of Prosthodontics and Implantology, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai, Tamil Nadu, India.
Aim: The purpose of this in vitro study was to compare the marginal fit of various three-dimensional (3D) printed and milled polymethylmethacrylate (PMMA) dental prostheses.
Settings And Design: The study was conducted in an in vitro study setting.
Materials And Methods: With a sample size of 45 for each fabrication method, this investigation compared the marginal fit of milled (Group 1) and 3D printed (Group 2) PMMA dental prostheses across different designs.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!