Objectives: This study aimed to compare the haptic perception of clinicians to the cutting response of 3D-printed typodont teeth and commercial typodont teeth and human extracted teeth.
Methods: Twenty clinicians were asked to perform a Class I cavity preparation on commercial typodont teeth, 3D-printed typodont teeth, and human extracted teeth, while the forces were recorded via a three-axis load cell. The haptic perception of clinicians was also evaluated through a response questionnaire comparing commercial and 3D-printed typodont teeth.
Results: The study found that clinicians used similar forces (p = 0.53) to cut both the 3D-printed typodont teeth (1.37 N) and the human extracted teeth (1.44 N), but more force was needed to cut the commercial typodont teeth (3.71 N). The response questionnaire indicated that clinicians rated the 3D-printed typodont teeth highly compared to the commercial teeth. The 3D-printed dentine received favorable feedback from clinicians, and the 3D-printed enamel was rated higher compared to the commercial equivalents.
Conclusions: The results of the study suggest that 3D-printed typodont teeth offer a comparable haptic perception to human extracted teeth and can be used as an effective tool for preclinical dental learning. Moreover, the study highlights the advantages of 3D-printed typodont teeth over commercial typodont teeth in terms of haptic perception.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1002/jdd.13749 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Design and Efficacy of Custom-Made Cleaning Splints for the Approximal Plaque Removal-A Laboratory Study.
J Clin Med
December 2024
Department of Prosthodontics, Medical Faculty, Heidelberg University, 69120 Heidelberg, Germany.
Cleaning splints (CSs) can facilitate interdental brush (IDB) insertion and guide IDBs during cleaning movement. Cleaning efficacy with and without CSs was to be assessed and compared for a fully dentate (FD) and a partially edentulous (PE) situation. For two maxillary typodont models simulating either an FD situation or a PE situation with every second tooth missing, suitable IDBs were selected and each cleaning splint was designed and fabricated by 3D-printing.
View Article and Find Full Text PDFFracture resistance and marginal fit of three different overlay designs using advanced zirconia-reinforced lithium disilicate CAD/CAM material.
BMC Oral Health
January 2025
Department of Conservative Dentistry, Faculty of Dentistry, Alexandria University, Alexandria, Egypt.
Background: Conservative dentistry introduced modern restoration designs, contributing to the greater use of partial-coverage ceramic restorations. New strong bondable ceramic materials made fabricating partial coverage ceramic restorations easier to restore the badly destructed teeth.
Aim Of The Study: This study investigated the impact of three distinct overlay preparation designs on the marginal fit (both before and after thermal aging) and the fracture resistance of overlay restorations fabricated using advanced zirconia-reinforced lithium disilicate (ALD) CAD/CAM glass-ceramic blocks.
Comparative evaluation of marginal fit accuracy of two different designs of endocrown manufactured through CAD-CAM system: An in vitro study.
J Indian Prosthodont Soc
January 2025
Department of Epidemiology, College of Medicine, University of Cincinnati, Ohio, USA.
Aims: To compare the accuracy of marginal fit of CAD-CAM endocrown with two different preparation forms, i.e., endocrown with ferrule and endocrown without ferrule.
View Article and Find Full Text PDFComparison of marginal fit between milled and three-dimensional printed polymethylmethacrylate prostheses for single crowns, anterior bridges, and pier abutment bridges: An in vitro study.
J Indian Prosthodont Soc
January 2025
Department of Prosthodontics and Implantology, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai, Tamil Nadu, India.
Aim: The purpose of this in vitro study was to compare the marginal fit of various three-dimensional (3D) printed and milled polymethylmethacrylate (PMMA) dental prostheses.
Settings And Design: The study was conducted in an in vitro study setting.
Materials And Methods: With a sample size of 45 for each fabrication method, this investigation compared the marginal fit of milled (Group 1) and 3D printed (Group 2) PMMA dental prostheses across different designs.
Influence of orthodontic bracket block-out materials on superimposition errors when substituting scanned dental imaging data onto computed tomography images.
Imaging Sci Dent
December 2024
Department of Oral and Maxillofacial Surgery, College of Dentistry, Yonsei University, Seoul, Korea.
Purpose: The study was performed to examine the error associated with image superimposition when computed tomography (CT) images of the dental region are substituted with dental scan data, according to the block-out material used in dental impressions.
Materials And Methods: A typodont model was created by bonding orthodontic brackets to teeth on plaster dental stones using melted dental base-plate wax. In the experiment, 2 groups were compared: one using wax and the other using putty as the block-out material to prevent tearing of the impression material during the acquisition of dental impressions.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!