Although anterior cervical discectomy and fusion (ACDF) is one of the most common surgical procedures performed for the treatment of cervical disease, it is associated with a variety of postoperative complications. Esophageal perforation is a rare but very serious post-ACDF complication, and cases in which screws extrude through the mouth are even rarer. Herein, we present the case of a 61-year-old woman who visited our emergency center with oral extrusion of a screw 6 months after undergoing ACDF. Although diagnostic imaging did not confirm esophageal perforation, the oral extrusion of the screw was clear evidence of the complication. To the best of our knowledge, this is the first reported case of oral screw extrusion without confirmed esophageal injury. This case suggests that screw migration and esophageal perforation can occur depending on the patient's underlying condition, and if the symptoms are mild, conservative treatment alone may be sufficient to treat the perforation.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11450344 | PMC |
| http://dx.doi.org/10.13004/kjnt.2024.20.e27 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Personalized Medicine Through Semisolid-Extrusion Based 3D Printing: Dual-Drug Loaded Gummies for Enhanced Patient Compliance.
Pharm Res
January 2025
Department of Pharmaceutics and Drug Delivery, School of Pharmacy, The University of Mississippi, University, MS, 38677, USA.
Purpose: The purpose of this research was to develop and characterize dual-drug Isoniazid-Pyridoxine gummies using Semisolid Extrusion (SSE) 3D printing technology, aimed at personalized dosing for a broad patient demographic, from pediatric to geriatric. This study leverages SSE 3D printing, an innovative approach in personalized medicine, to enable precise dose customization and improve patient adherence. By formulating dual drug-loaded gummies, the research addresses the challenges of pill burden and poor palatability associated with traditional tuberculosis regimens, ultimately enhancing the therapeutic experience and effectiveness for patients across various age groups.
View Article and Find Full Text PDFBioceramics for Guided Bone Regeneration: A Multicenter Randomized Controlled Trial.
Clin Implant Dent Relat Res
February 2025
State Key Laboratory of Oral & Maxillofacial Reconstruction and Regeneration, Key Laboratory of Oral Biomedicine Ministry of Education, Hubei Key Laboratory of Stomatology, School & Hospital of Stomatology, Wuhan University, Wuhan, China.
Objectives: To compare the clinical effectiveness of a novel bioceramic (BC) with a control xenograft (BO) for guided bone regeneration (GBR) performed simultaneously with implant placement.
Materials And Methods: This clinical study enrolled patients with insufficient bone volume who required GBR during implant placement to increase bone width using either BC or BO. Outcome measures included a dimensional reduction in buccal bone thickness measured by cone beam computed tomography performed immediately post-surgery and at 6 months postoperatively (ΔHBBT), soft tissue healing at 14 days, 1 month, and 6 months postoperatively, and complications rates.
[How I treat… An open bite secondary to ankylosis of a primary molar tooth].
Rev Med Liege
January 2025
Service de Dentisterie conservatrice, endodontie et pédodontie, CHU Liège, Belgique.
Infraclusion is a consequence of dentoalveolar ankylosis. Associated complications include extrusion of the opposing tooth, open bites, and tilts. Early detection and management are crucial to limit and/or correct these complications.
View Article and Find Full Text PDFTenderness in meat and meat alternatives: Structural and processing fundamentals.
Compr Rev Food Sci Food Saf
January 2025
Department of Food Science, University of Massachusetts Amherst, Amherst, Massachusetts, USA.
The demand for meat alternatives based on ingredients sourced from nonanimal materials with equivalent quality of muscle tissue is increasing. As more consumers switch to meat alternatives, a growing body of research has investigated the tenderness and related texture attributes in plant-based meats to increase consumer acceptance. A deeper understanding of tenderness including the differences and similarities between meat and meat alternatives is crucial to developing products that meet consumer expectations, as it directly influences consumer acceptance.
View Article and Find Full Text PDFExploring 3D Printing in Drug Development: Assessing the Potential of Advanced Melt Drop Deposition Technology for Solubility Enhancement by Creation of Amorphous Solid Dispersions.
Pharmaceutics
November 2024
Merck Life Science KGaA, Frankfurter Straße 250, 64293 Darmstadt, Germany.
Melt-based 3D printing technologies are currently extensively evaluated for research purposes as well as for industrial applications. Classical approaches often require intermediates, which can pose a risk to stability and add additional complexity to the process. The Advanced Melt Drop Deposition (AMDD) technology, is a 3D printing process that combines the principles of melt extrusion with pressure-driven ejection, similar to injection molding.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!