This study aims to optimize the performance of CrN coatings deposited on WC cutting tools for machining Ti6Al4V alloy, where the formation of built-up edge (BUE) is a prevalent and critical issue. In-house CrN coatings were developed using the PVD (Physical Vapor Deposition) process, with variations in deposition parameters including nitrogen gas pressure, bias voltage, and coating thickness. A comprehensive experimental approach encompassing deposition, characterization, and machining performance evaluation was employed to identify the optimal deposition conditions. The results indicated that CrN coatings deposited at a nitrogen gas pressure of 4 Pa, a bias voltage of -50 V, and a thickness of 1.81 µm exhibited superior performance, significantly reducing BUE formation and tool wear. These optimized coatings demonstrated enhanced properties, such as a higher elastic modulus and a lower coefficient of friction, which contributed to improved tool life and machining performance. Comparative studies with commercial CrN coatings revealed that the in-house developed coatings outperformed the commercial variants by approximately 65% in tool life, owing to their superior mechanical properties and reduced friction. This research highlights the potential of tailored CrN coatings for advanced machining applications and emphasizes the importance of optimizing deposition parameters to achieve high-performance tool coatings.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11395842 | PMC |
| http://dx.doi.org/10.3390/ma17174328 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Detailed Analysis of the Debris-Fretting Damage Areas on Coated Fuel Cladding.
Materials (Basel)
January 2025
Centrum Výzkumu Řež s.r.o., Hlavní 130, 250 68 Husinec-Řež, Czech Republic.
Fuel failure caused by fretting damage to cladding remains a relevant issue despite decades of research and development aimed at enhancing the physical parameters of fuel. This paper presents the results of experiments conducted at the Research Centre Řež on Zr-1%Nb alloy tube specimens covered with protective coatings made of chromium (Cr) and nitrogen (N) compounds. The experiments involved debris-fretting tests under dry conditions at room temperature as well as microscopic measurements of groove depths.
View Article and Find Full Text PDFInfluence of Nitrogen Content on the Microstructure Evolution and Oxidation Resistance toward Ambient Air of CrAlSiN Coatings Deposited by FCVAD Technique.
ACS Appl Mater Interfaces
November 2024
Key Laboratory of Beam Technology of the Ministry of Education, School of Physics and Astronomy, Beijing Normal University, Beijing 100875, China.
Article Synopsis
- - The study examined CrAlSiN coatings with varying nitrogen content (42 to 54 at. %) and tested their microstructure and oxidation resistance at high temperatures (700 or 900 °C).
- At lower nitrogen levels (42-45 at. %), the coatings displayed a hybrid amorphous/nanocrystalline structure, while higher nitrogen contents (above 52 at. %) resulted in a columnar structure dominated by Cr(Al)N.
- The optimal nitrogen content of around 52 at. % provided the best oxidation resistance, characterized by a stable AlO-rich monolayer, while lower nitrogen coatings formed thicker CrO layers and showed elemental segregation after high-temperature exposure.
Influence of punch coating surface properties on sticking during the tableting process.
Pharm Dev Technol
November 2024
Department of Chemical and Biotechnological Engineering, Université de Sherbrooke, Sherbrooke, QC, Canada.
Article Synopsis
- The study investigates how different punch coatings (Uncoated steel, CrN, ZrN, TiN, and Ultracoat) affect the sticking of microcrystalline cellulose (MCC) during the tableting process with a Manesty F3 press.
- The analysis focused on surface properties like roughness, free energy, and functional groups, revealing that TiN and uncoated steel had the highest adhesion to MCC after pressing.
- Results indicated that surfaces with higher Lewis base components in their surface free energy were more prone to sticking due to stronger interactions with evaporating water, and a high percentage of polar functional groups also contributed to this behavior.
Numerical Analysis of Cavitation Erosion in 316L Steel with CrN PVD Coating.
Materials (Basel)
September 2024
Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Hydropower Department, Fiszera 14 St., 80-231 Gdansk, Poland.
The erosion process of a 4 μm monolayer CrN coating deposited on 316L stainless steel due to cavitation was investigated using finite element analysis (FEA). To estimate load parameters from cavitation pit geometry resulting from high impact velocity and high strain rate, the explicit dynamic solver was employed. Water microjet impacts at velocities of 100, 200 and 500 m/s were simulated to recreate different cavitation erosion intensities observed in the experiment.
View Article and Find Full Text PDFEffect of Deposition Parameters on Micromechanical Properties and Machining Performance of CrN Coating for Wet Finish Turning of Ti6Al4V Alloy.
Materials (Basel)
August 2024
McMaster Manufacturing Research Institute (MMRI), Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, ON L8S 4L7, Canada.
This study aims to optimize the performance of CrN coatings deposited on WC cutting tools for machining Ti6Al4V alloy, where the formation of built-up edge (BUE) is a prevalent and critical issue. In-house CrN coatings were developed using the PVD (Physical Vapor Deposition) process, with variations in deposition parameters including nitrogen gas pressure, bias voltage, and coating thickness. A comprehensive experimental approach encompassing deposition, characterization, and machining performance evaluation was employed to identify the optimal deposition conditions.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!