Modifying food texture is a valuable approach to enhancing the quality of life for patients with dysphagia. Incorporating thickened soy protein-based liquid systems (SPLS) into their diet not only improves protein intake but also promotes safer swallowing. However, the properties of thickened SPLS are crucial for safe swallowing, may vary depending on the conformation of the thickened polysaccharides used. In this study, SPLS with different levels of thickening were prepared using xanthan gum, pectin and guar gum. The influence of polysaccharide conformation on the rheological (shear and extensional) and tribological properties of thickened SPLS was investigated. The results revealed that xanthan gum-thickened SPLS exhibiting the highest shear viscosity (110.073 Pa.s) and extensional viscosity (7.405 Pa.s), which increased with polysaccharide concentration. Meanwhile, xanthan gum possessed the strongest lubricating properties. These results shed light on the development of plant protein-based solutions for dysphagia management.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.foodchem.2024.141145DOI Listing

Publication Analysis

Top Keywords

shear extensional
8
soy protein-based
8
protein-based liquid
8
liquid systems
8
dysphagia management
8
properties thickened
8
thickened spls
8
xanthan gum
8
spls
5
extensional rheology
4

Similar Publications

Simultaneous processing of both handheld biomixing and biowriting of kombucha cultured pre-crosslinked nanocellulose bioink for regeneration of irregular and multi-layered tissue defects.

Int J Biol Macromol

December 2024

Department of Chemical and Biomolecular Engineering, Seoul National University of Science and Technology, Seoul 01811, Republic of Korea; Convergence Institute of Biomedical Engineering and Biomaterials, Seoul National University of Science and Technology, Seoul 01811, Republic of Korea. Electronic address:

The nanocellulosic pellicle derived from the symbiotic culture of bacteria and yeast (Kombucha SCOBY) is an important biomaterial for 3D bioprinting in tissue engineering. However, this nanocellulosic hydrogel has a highly entangled gel network. This needs to be partially modified to improve its processability and extrusion ability for its applications in the 3D bioprinting area.

View Article and Find Full Text PDF

Enhancing melt strength and crystallization kinetics in polylactide: Influence of chain topology.

Int J Biol Macromol

December 2024

POLYMAT and Department of Advanced Polymers and Materials: Physics, Chemistry and Technology, Faculty of Chemistry, University of the Basque Country UPV/EHU, Paseo Manuel de Lardizabal 3, 20018 Donostia-San Sebastián, Spain; IKERBASQUE, Basque Foundation for Science, Plaza Euskadi 5, 48009 Bilbao, Spain. Electronic address:

The generation of long-chain branches (LCB) in biobased and biodegradable polylactide (PLA) by adding different amounts of a chain extender is studied. The rheological and calorimetric behavior have been used to determine the effect of LCB presence and their topology on PLA melt strength and crystallization behavior. Rheological modeling of linear and non-linear viscoelastic shear and extensional properties identified several possible branched structures.

View Article and Find Full Text PDF

Drop deformation in a planar elongational flow: impact of surfactant dynamics.

Soft Matter

November 2024

Université Paris-Saclay, CNRS, Laboratoire de Physique des Solides, 91405 Orsay, France.

Drops in extensional flow undergo a deformation, which is primarily fixed by a balance between their surface tension and the viscous stress. This deformation, predicted and measured by Taylor on millimetric drops, is expected to be affected by the presence of surfactants but has never been measured systematically. We provide a controlled experiment allowing us to measure this deformation as a function of the drop size and of the shear stress for different surfactants at varying concentrations.

View Article and Find Full Text PDF

In the realm of tissue engineering, replicating the intricate alignment of cells and the extracellular matrix (ECM) found in native tissue has long been a challenge. Most recent studies have relied on complex multi-step processes to approximate native tissue alignment. To address this challenge, we introduce a novel, single-step method for constructing highly aligned fibrous structures within multi-modular three-dimensional conglomerates.

View Article and Find Full Text PDF

Enhanced oil recovery (EOR) methods are generally employed in depleted reservoirs to increase the recovery factor beyond that of water flooding. Polymer flooding is one of the major EOR methods. EOR polymer solutions (especially the synthetic ones characterized by flexible chains) that flow through porous media are not only subjected to shearing forces but also extensional deformation, and therefore, they exhibit not only Newtonian and shear thinning behavior but also shear thickening behavior at a certain porous media shear rate/velocity.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!