Introduction: Sufficient perfusion is essential for a safe intestinal anastomosis. Impaired microcirculation may lead to increased bacterial translocation and anastomosis insufficiency. Thus, it is important to estimate well the optimal distance of the anastomosis line from the last mesenterial vessel. However, it is still empiric. In this experiment the aim was to investigate the intestinal microcirculation at various distances from the anastomosis in a pig model.
Materials And Methods: On 8 anesthetized pigs paramedian laparotomy and end-to-end jejuno-jejunostomy were performed. Using Cytocam-IDF camera, microcirculatory recordings were taken before surgery at the planned suture line, and 1 to 3 mesenterial vessel mural trunk distance from it, and at the same sites 15 and 120 min after anastomosis completion. After the microcirculation monitoring, anastomosed and intact bowel segments were removed to test tensile strength.
Results: The proportion and the density of the perfused vessels decreased significantly after anastomosis completion. The perfusion rate increased gradually distal from the anastomosis, and after 120 min these values seemed to be normalized. Anastomosed bowels had significantly lower maximal tensile strength and higher slope of tensile strength curves than intact controls.
Conclusion: Alterations in microcirculation and tensile strength were observed. After completing the anastomosis, the improvement in perfusion increased gradually away from the wound edge. The IDF device was useful to monitor intestinal microcirculation providing data to estimate better the optimal distance of the anastomosis from the last order mesenteric vessel.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.mvr.2024.104731 | DOI Listing |
Sci Rep
January 2025
Research Center of Traffic Disaster Prevention and Mitigation, Jilin Jianzhu University, Jilin Jianzhu University, Xincheng Street, Changchun, 130118, Jilin, China.
To promote the recycling of waste glass and satisfy the demands of environmental sustainability for ultrahigh performance concrete (UHPC), in this study, glass sand was employed to partially or entirely replace machine-made sand, and steel fibres were incorporated to fabricate ultrahigh performance shotcrete (UHPS). The effects of glass sand and steel fibres on the mechanical and electrical properties of composite materials were analysed in this study. Furthermore, alkali‒silica reaction (ASR) tests and microstructural analyses were conducted.
View Article and Find Full Text PDFSci Rep
January 2025
Research Center for Applied Chemistry, Blvd Enrique Reyna 140, San José de los Cerritos, Saltillo, 25294, Mexico.
As the rubber industry seeks sustainable alternatives to mitigate its environmental impact, this study introduces a biobased approach using polyfarnesene rubber reinforced with plasma-modified cellulose nanocrystals (MCNC) and nanofibers (MCNF). The nanocellulose was modified by plasma-induced polymerization using trans-β-farnesene and was characterized by FTIR, XPS, XRD, TGA, and SEM to confirm the grafting of farnesene-derived polymer chains onto the cellulose surface, demonstrating the successful modification and integration of the nanoparticles. Polyfarnesene bio-based rubbers were synthesized through two different polymerization techniques: solution-based coordination polymerization (PFA1) and emulsion-based free radical polymerization (PFA2).
View Article and Find Full Text PDFInt J Biol Macromol
January 2025
College of Chemistry, Beijing University of Chemical Technology, Beijing 100029, People's Republic of China. Electronic address:
The advancement of active packaging for food conservation has attracted considerable interest over time. In the present study, we aims to create and examine active films composed of chitosan (CS), poly(vinyl alcohol) (PVA), and syzygium guineense plant extract (SYZ) for potential use in food preservation. We examined the impact of ethanol extracts from the SYZ plant on the films' tensile strength, physical, antibacterial, and anti-oxidant properties.
View Article and Find Full Text PDFInt J Biol Macromol
January 2025
Hubei Provincial Engineering Laboratory for Clean Production and High Value Utilisation of Bio-based Textile Materials, Wuhan Textile University, Wuhan 430200, China; Engineering Research Centre for Clean Production of Textile Dyeing and Printing, Ministry of Education, Wuhan Textile University, Wuhan 430200, China. Electronic address:
The conventional method of dyeing cellulose diacetate (CDA) fabric with disperse dyes consumes significant amounts of fresh water and dispersants, contributing to environmental pollution and health hazards. This study explored the use of liquid paraffin as an alternative to aqueous mediums for dyeing CDA fabric with Disperse Blue 56 dyes, eliminating the need for dispersants. An L orthogonal array was used to optimize dyeing conditions based on the color strength values.
View Article and Find Full Text PDFScience
January 2025
Center for Advancing Materials Performance from the Nanoscale (CAMP-Nano), Hysitron Applied Research Center in China (HARCC) and Center for Alloy Innovation and Design (CAID), State Key Laboratory for Mechanical Behavior of Materials, Xi'an Jiaotong University, Xi'an, China.
Higher strength and higher ductility are desirable for structural materials. However, ultrastrong alloys inevitably show decreased strain-hardening capacity, limiting their uniform elongation. We present a supranano (<10 nanometers) and short-range ordering design for grain interiors and grain boundary regions, respectively, in fine-grained alloys based on vanadium, cobalt, and nickel, with additions of tungsten, copper, aluminum, and boron.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!