In this article, the zonotopic distributed fusion estimation problem is investigated for a class of general nonlinear systems over binary sensor networks subject to unknown-but-bounded (UBB) noises. The network communication from nodes to the fusion center is confined to the limited bit rate. To alleviate the impact from less measurement information of the binary sensor, a modified innovation is constructed to improve the estimation accuracy. Then, a novel coding-decoding approach is proposed to ensure that the decoder has the ability to decode information from each node. Based on the matrix weighting fusion method, a distributed fusion algorithm is put forward under the zonotopic set-membership filtering framework, and the F-radius of the local zonotopic sets are derived and minimized by selecting the filtering gain parameters. Moreover, the bit rate allocation scheme and the weighting coefficients are determined by resolving two optimization problems. In addition, a sufficient condition is established to guarantee the uniform boundedness of the F-radius of the fused zonopotic. Finally, the ballistic object tracking systems is utilized to illustrate the availability of the presented algorithm.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1109/TCYB.2024.3419033 | DOI Listing |
Sci Rep
January 2025
School of Electronic and Information Engineering, Changsha Institute of Technology, Changsha, 410200, China.
In order to solve the limitations of flipped classroom in personalized teaching and interactive effect improvement, this paper designs a new model of flipped classroom in colleges and universities based on Virtual Reality (VR) by combining the algorithm of Contrastive Language-Image Pre-Training (CLIP). Through cross-modal data fusion, the model deeply combines students' operation behavior with teaching content, and improves teaching effect through intelligent feedback mechanism. The test data shows that the similarity between video and image modes reaches 0.
View Article and Find Full Text PDFSensors (Basel)
January 2025
School of Oceanography and Spatial Information, China University of Petroleum East China-Qingdao Campus, Qingdao 266580, China.
Salt marsh vegetation in the Yellow River Delta, including (), (), and (), is essential for the stability of wetland ecosystems. In recent years, salt marsh vegetation has experienced severe degradation, which is primarily due to invasive species and human activities. Therefore, the accurate monitoring of the spatial distribution of these vegetation types is critical for the ecological protection and restoration of the Yellow River Delta.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Department of Electrical Engineering, Universidade Federal do Espírito Santo, Vitória 29075-910, ES, Brazil.
The increasing demand for autonomous mobile robots in complex environments calls for efficient path-planning algorithms. Bio-inspired algorithms effectively address intricate optimization challenges, but their computational cost increases with the number of particles, which is great when implementing algorithms of high accuracy. To address such topics, this paper explores the application of the leader-based bat algorithm (LBBA), an enhancement of the traditional bat algorithm (BA).
View Article and Find Full Text PDFMaterials (Basel)
January 2025
Mechanical and Aerospace Engineering Department, Utah State University, Logan, UT 84322-4130, USA.
Laser powder bed fusion (LPBF) is an additive manufacturing process that has gained interest for its material fabrication due to multiple advantages, such as the ability to print parts with small feature sizes, good mechanical properties, reduced material waste, etc. However, variations in the key process parameters in LPBF may result in the instantiation of porosity defects and variation in build rate. Particularly, volumetric energy density (VED) is a variable that encapsulates a number of those parameters and represents the amount of energy input from the laser source to the feedstock.
View Article and Find Full Text PDFMaterials (Basel)
January 2025
Department of Biomedical Engineering, Iwate Medical University, Iwate 028-3694, Japan.
This study aimed to investigate the release of metallic ions from cobalt-chromium (Co-Cr) alloys fabricated by additive manufacturing (AM) for comparison with dental casting. Co-Cr alloys were fabricated via AM using selective laser melting (SLM) and electron beam melting (EBM) in powder-bed fusion. Polished and mechanically ground specimens were prepared.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!