Polymer networks with controlled ratios of neutral and ionic dynamic crosslink points were prepared from ethylene glycol, boric acid, and lithium hydroxide. Both neutral and ionic sites led to the emergence of distinct damping modes separate from the glass transition. This work highlights the potential of polymer networks for multimodal damping spectra through dynamic bond selection.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1039/d4cc02013h | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Electrically conducting porous hydrogels by a self-assembled percolating pristine graphene network.
Soft Matter
January 2025
Department of Chemistry, University of Connecticut, Storrs, Connecticut, USA.
This study introduces a method for synthesizing electrically conductive hydrogels by incorporating a self-assembled, percolating graphene network. Our approach differs from previous approaches in two crucial aspects: using pristine graphene rather than graphene oxide and self-assembling the percolation network rather than creating random networks by blending. We use pristine graphene at an oil-water interface to stabilize a water-in-oil emulsion, successfully creating hydrogel foams with conductivities up to 15 mS m and tunable porosity.
View Article and Find Full Text PDFEnhanced room temperature ammonia gas sensing based on a multichannel PSS-functionalized graphene/PANI network.
Analyst
January 2025
Guangdong Provincial Key Laboratory of Electronic Functional Materials and Devices, Huizhou University, Huizhou, 516007, China.
Disordered polymerization of polymers widens the polymerization degree distribution, which leads to uncontrollable thickness and significantly weakens their sensing performance. Herein, poly(sodium -styrenesulfonate)-functionalized reduced graphene oxide (PSS-rGO) with multichannel chain structures coated with thin polyaniline layer (PSS-rGO/PANI) nanocomposites was synthesized a facile interfacial polymerization route. The morphology and microstructure of the PSS-rGO/PANI nanocomposites were characterized using Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM).
View Article and Find Full Text PDFCollagen deposition in lung parenchyma driven by depletion of interstitial Lyve-1 macrophages prevents cigarette smoke-induced emphysema and loss of airway function.
Front Immunol
January 2025
Immunology Translational Research Programme, Yong Loo Lin School of Medicine, Department of Microbiology & Immunology, National University of Singapore, Singapore, Singapore.
Introduction: Collagen is essential for maintaining lung structure and function and its remodeling has been associated with respiratory diseases including chronic obstructive pulmonary disease (COPD). However, the cellular mechanisms driving collagen remodeling and the functional implications of this process in the pathophysiology of pulmonary diseases remain poorly understood.
Methods: To address this question, we employed ; mice with specific depletion of Lyve-1 macrophages and assessed the content, types and organization of collagen in lung compartments at steady state and after chronic exposure to cigarette smoke (CS).
A bio-inspired microwave wireless system for constituting passive and maintenance-free IoT networks.
Natl Sci Rev
February 2025
State Key Laboratory of Millimeter Waves, School of Information Science and Engineering, Southeast University, Nanjing 210096, China.
With the rapid expansion of wireless networks, the deployment and long-term maintenance of distributed microwave terminals have become increasingly challenging. To address these issues, we present a bio-inspired microwave system to constitute passive and maintenance-free wireless networks. Drawing inspiration from vertebrate skeletons and skins, we employ stimuli-responsive polymer with tunable stiffness to support and protect sensitive electromagnetic structures, and synthesize self-healable skin-like polymer for system encapsulation.
View Article and Find Full Text PDFFunctional hydrogel empowering 3D printing titanium alloys.
Mater Today Bio
February 2025
Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, Jilin, China.
Titanium alloys are widely used in the manufacture of orthopedic prosthesis given their excellent mechanical properties and biocompatibility. However, the primary drawbacks of traditional titanium alloy prosthesis are their much higher elastic modulus than cancellous bone and poor interfacial adhesion, which lead to poor osseointegration. 3D-printed porous titanium alloys can partly address these issues, but their bio-inertness still requires modifications to adapt to different physiological and pathological microenvironments.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!