Objectives: To assess the extent of staff exposure to aerosol generation in common pediatric otorhinolaryngological procedures (tonsillotomies, adenoidectomies, and tympanostomies) and determine the surgical phases responsible for most aerosol generation in these procedures.
Methods: Aerosol generation was measured during 35 pediatric otolaryngological procedures using an Optical Particle Sizer that measures aerosol concentrations for particle sizes between 0.3 and 10.0 μm. The different phases of and instruments used in each procedure were logged. Operating room background aerosol levels and coughing were used as references.
Results: Total aerosol concentrations were significantly higher during tonsillotomies and adenoidectomies when compared to tympanostomies (p = 0.011 and p = 0.042) and to empty room background aerosol concentrations (p = 0.0057 and p < 0.001). Aerosol concentration during tonsillotomies did not differ from coughing, which is considered as standard for high-risk aerosol procedures. During tympanostomies, aerosol concentrations were even lower than during perioperative concentrations. No statistically significant difference in aerosol generation comparing suction, electrocautery, cold instruments, and paracentesis was found.
Conclusion: According to the results of this study, tympanostomies are low-risk aerosol-generating procedures. On the other hand, pediatric tonsillotomies produced aerosols comparable to coughing, pointing to them being significantly aerosol-producing procedures and viral transmission is theoretically possible intraoperatively.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.ijporl.2024.112030 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Association of Mycobacterium tuberculosis aerosolization and HIV coinfection in the index case with T cell responses in household contacts.
Sci Rep
January 2025
Department of Global Health, University of Washington, Seattle, WA, USA.
Exposure to pulmonary tuberculosis (PTB) culminates in heterogeneous outcomes, including variation in Mtb antigen-specific interferon-gamma (IFN-γ) T-cell responses. IFN-γ-independent cytokines, including tumor necrosis factor (TNF) and interleukin (IL-2), offer potential diagnostic improvements and insights into pathogenesis. We hypothesized that ESAT6/CFP10 TNF and IL-2 responses improve Mtb infection detection among exposed household contacts (HHCs) and are associated with index case Mtb aerosolization (i.
View Article and Find Full Text PDFSolar energy resource availability under extreme and historical wildfire smoke conditions.
Nat Commun
January 2025
Department of Atmospheric Science, Colorado State University, Fort Collins, CO, USA.
By 2050, the U.S. plans to increase solar energy from 3% to 45% of the nation's electricity generation.
View Article and Find Full Text PDFMolecular insights into the composition, sources, and aging of atmospheric brown carbon.
Chem Soc Rev
January 2025
Department of Chemistry, Purdue University, West Lafayette, Indiana, 47906, USA.
The light-absorbing chemical components of atmospheric organic aerosols are commonly referred to as Brown Carbon (BrC), reflecting the characteristic yellowish to brown appearance of aerosol. BrC is a highly complex mixture of organic compounds with diverse compositions and variable optical properties of its individual chromophores. BrC significantly influences the radiative budget of the climate and contributes to adverse air pollution effects such as reduced visibility and the presence of inhalable pollutants and irritants.
View Article and Find Full Text PDFPrinting rare-earth-free (REF) magnetic inks: synthesis, formulation, and device applications.
Nanoscale
January 2025
Department of Chemical Engineering, Texas Tech University, Lubbock, TX 79409, USA.
Additive manufacturing (AM) of magnetic materials has recently attracted increasing interest for various applications but is often limited by the high cost and supply chain risks of rare-earth-element (REE) magnetic precursors. Recent advances in nanomanufacturing have enabled the development of rare-earth-free (REF) magnetic materials, such as spinel ferrites, hexaferrites, MnAl, MnBi, Alnico, FePt, and iron oxides/nitrides, which offer promising alternatives for printing high-performance magnetic devices. This review provides a detailed overview of the latest developments in REF magnetic materials, covering both synthesis strategies of REF magnetic materials/nanomaterials and their integration into AM processes.
View Article and Find Full Text PDFDesign and Evaluation of 3D-Printed Lattice Structures as High Flow Rate Aerosol Filters.
ACS Appl Eng Mater
December 2024
Department of Chemical and Biomolecular Engineering and Department of Biomedical Engineering, University of Delaware, 150 Academy Street, Newark, Delaware 19716, United States.
Aerosol contamination presents significant challenges across various industries, ranging from healthcare to manufacturing. Over the past few years, open foam filters have gained prominence for their ability to efficiently capture particles while allowing reasonable airflow. In this work, we present the use of 3D-printed idealized open foam-like lattice structures as aerosol filtration media, leveraging advances in additive manufacturing to generate these highly tunable and modular filters.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!