Head impacts are a major concern in contact sports and sports with high-speed mobility due to the prevalence of head trauma events and their dire consequences. Surrogates of human heads are required in laboratory testing to safely explore the efficacy of impact-mitigating mechanisms. This work proposes using polymer additive manufacturing technologies to obtain a substitute for the human skull to be filled with a silicone-based brain surrogate. This assembly was instrumentalized with an Inertial Measurement Unit. Its performance was compared to a standard Hybrid III head form in validation tests using commercial headgear. The tests involved impact velocities in a range centered around 5 m/s. The results show a reasonable homology between the head substitutes, with a disparity in the impact response within 20% between the proposed surrogate and the standard head form. The head surrogate herein developed can be easily adapted to other morphologies and will significantly decrease the cost of the laboratory testing of head protection equipment, all while ensuring the safety of the testing process.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11207555 | PMC |
| http://dx.doi.org/10.3390/polym16121753 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
E-jet printed polycaprolactone with strontium-substituted mesoporous bioactive glass nanoparticles for bone tissue engineering.
Biomater Adv
January 2025
Department of Orthopaedic Surgery, National University of Singapore, NUHS Tower Block, Level 11, 1E Kent Ridge Road, Singapore 119228, Singapore.
Osteoporosis, characterized by reduced bone mineral density and increased fracture risk, poses a significant health challenge, particularly for aging populations. Systemic treatments often lead to adverse side effects, emphasizing the need for localized solutions. This study introduces a 3D-printed polycaprolactone (PCL) scaffold embedded with strontium-substituted mesoporous bioactive glass nanoparticles (Sr-MBGNPs) and icariin (ICN) for the targeted regeneration of osteoporotic bone.
View Article and Find Full Text PDFLignin alkali regulated interfacial polymerization towards ultra-selective and highly permeable nanofiltration membrane.
Nat Commun
January 2025
School of Environmental Science and Engineering, Sun Yat-sen University, Guangzhou, China.
Thin-film composite polyamide (TFC PA) membranes hold promise for energy-efficient liquid separation, but achieving high permeance and precise separation membrane via a facile approach that is compatible with present manufacturing line remains a great challenge. Herein, we demonstrate the use of lignin alkali (LA) derived from waste of paper pulp as an aqueous phase additive to regulate interfacial polymerization (IP) process for achieving high performance nanofiltration (NF) membrane. Various characterizations and molecular dynamics simulations revealed that LA can promote the diffusion and partition of aqueous phase monomer piperazine (PIP) molecules into organic phase and their uniform dispersion on substrate, accelerating the IP reaction and promoting greater interfacial instabilities, thus endowing formation of TFC NF membrane with an ultrathin, highly cross-linked, and crumpled PA layer.
View Article and Find Full Text PDFSynthesis and characterization of dextran palmitate for extrusion 3D printing.
Int J Biol Macromol
January 2025
KU Leuven, Department of Chemical Engineering, Chemical and Biochemical Reactor Engineering and Safety (CREaS), Celestijnenlaan 200F, 3001 Leuven, Belgium. Electronic address:
The fabrication of objects with complex shape and geometry has been greatly facilitated with the advancements in additive manufacturing. While synthetic polymers like ABS and PLA have found widespread use in extrusion 3D printing, other biobased thermoplastics that are both biodegradable and biocompatible could offer strategic advantages over traditional synthetic materials. In this work dextran of low (20 kDa) and medium (40 kDa) molecular weight (MW) was modified with palmitic acid to obtain meltable polymers for extrusion 3D printing/fused deposition modeling additive manufacturing.
View Article and Find Full Text PDFMultiphoton and Harmonic Imaging of Microarchitected Materials.
ACS Appl Mater Interfaces
January 2025
Laser Thermal Laboratory, Department of Mechanical Engineering, University of California, Berkeley, California 94720, United States.
Article Synopsis
- Microadditive manufacturing enables the creation of intricate nano- and microscale components, leading to advancements in various industries.
- This research explores two-photon and three-photon fluorescence imaging, along with third-harmonic generation microscopy, to analyze complex lattice structures produced by multiphoton lithography.
- The study reveals that multiphoton fluorescence imaging provides better depth penetration and nondestructive identification of internal modifications and defects, improving quality control in microadditively manufactured products.
IPEM topical report: guidance on 3D printing in radiotherapy.
Phys Med Biol
January 2025
Department of Physics, UCLH NHS Foundation Trust, 250 Euston Road,, London, NW1 2PG, UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND.
There has been an increase in the availability and utilization of commercially available 3D printers in radiotherapy, with applications in phantoms, brachytherapy applicators, bolus, compensators, and immobilization devices. Additive manufacturing in the form of 3D printing has the advantage of rapid production of personalized patient specific prints or customized phantoms within a short timeframe. One of the barriers to uptake has been the lack of guidance.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!