Mitigation of methane (CH) emissions from slurry pits within pig barns can be achieved through treatment of residual slurry left after frequent flushing of the slurry pits. In this study, dosages of additives such as sodium dodecyl sulfate (SDS) and hydrogen peroxide (HO) were optimized to achieve reduction in CH emissions from residual pig slurry during storage. In addition, the effects on emissions when both the treatments were combined and the effects of SDS treatment on slurry acidified with sulfuric acid (HSO) were studied in order to reduce CH and ammonia (NH) emissions from residual pig slurry storage. A maximum of 98% and 70% reduction in CH emissions were achieved with SDS and HO treatments, respectively. The combination of SDS and HO did not increase efficiency in reducing CH emissions compared to SDS treatment alone. Whereas the application of SDS to slurry acidified with HSO (pH 6.2) increased the CH mitigation efficiency by 15-30% compared to treating slurry with only SDS. The combined treatment (SDS + HSO) reduced NH emissions by 20% compared to treating slurry with HSO (pH 6.2) alone. Hereby, combined treatment (SDS + HSO) can reduce both CH and NH emissions, with a reduced amount of chemicals required for the treatment. Hence, application of SDS at concentrations <2 g kg to acidified slurry is recommended to treat residual pig manure in pig barns.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.jenvman.2024.121415 | DOI Listing |
ACS Omega
December 2024
Norin Mining Limited, Beijing 100053, China.
With the continuous exploitation of global mineral resources, backfill technology for gob areas has become a crucial aspect of mine safety and sustainable development. As a primary method of gob area backfill, slurry backfill directly relates its flow properties and filling height to the efficiency and safety of mine extraction. To enhance the flow properties of the slurry and increase its filling height, a research study on the flow and deposition characteristics of a gas-containing filling slurry was conducted using a combination of theoretical analysis, laboratory experiments, and field tests.
View Article and Find Full Text PDF3D Print Addit Manuf
October 2024
State Key Laboratory of Materials Processing and Die and Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan, China.
The optimization of slurry content and forming process parameters has a significant effect in slurry microextrusion direct forming method. In this article, magnesium sulfate monohydrate (MgSO) and polyvinylpyrrolidone (PVP) were used as raw materials to prepare the slurry, and the component ratios of the slurry and the optimization of its forming process were discussed. The optimum slurry content is 64 wt.
View Article and Find Full Text PDF3D Print Addit Manuf
October 2024
School of Mechanical Engineering (Shandong Institute of Mechanical Design and Research), Qilu University of Technology (Shandong Academy of Sciences), Jinan, China.
Digital light processing is a recently developed solution to fabricate complex structured piezoelectric devices. To obtain a high-performance device, the slurry configuration, model slicing, and heat treatment methods during the printing should be carefully determined. In this article, 200 nm particle size barium titanate powders with an optimized solid content of 80% (mass fraction) were used to configure the slurry with higher printing efficiency.
View Article and Find Full Text PDF3D Print Addit Manuf
October 2024
Design Department, Gemmological Institute, China University of Geosciences, Wuhan, P.R. China.
Direct ink writing of multiple mineral materials (M) coupled with simulation analysis is an optimization solution in accordance with low-carbon and sustainable manufacturing. It improves the ability to imitate natural biological iterative optimization, and accurately obtained data for geological model tests to effectively help prevent natural disasters. This article investigates the effects of equivalent materials on the direct ink writing and permeability behaviors through geological simulation models.
View Article and Find Full Text PDFBioresour Bioprocess
December 2024
Production Systems Unit, Grasslands and Sustainable Agriculture Group, Natural Resources Institute Finland (Luke), Maaninka, FI-71750, Finland.
Thermal processes are emerging as promising solutions to recovering phosphorus and other nutrient elements from anaerobic digestates. The feasibility of nutrient element recovery depends largely on the fates of nutrient elements and heavy metals during thermal processing. This study assesses the partitioning of macronutrients (N, P, K, Na, Ca and Mg) and heavy metals (Zn, Cu, and Mn) between condensed and gaseous phases during thermal conversion of cattle slurry digestates in gas atmospheres of pyrolysis, combustion, and gasification processes.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!