Rapid and accurate determination of pigment content is important for quality inspection of spinach leaves during storage. This study aimed to use hyperspectral imaging at two spectral ranges (visible/near-infrared, VNIR: 400-1000 nm; NIR: 900-1700 nm) to simultaneously determine the pigment (chlorophyll , chlorophyll , total chlorophyll, and carotenoids) content in spinach stored at different durations and conditions (unpackaged and packaged). Partial least squares (PLS), back propagation neural network (BPNN) and convolutional neural network (CNN) were used to establish single-task and multi-task regression models. Single-task CNN (STCNN) models and multi-task CNN (MTCNN) models obtained better performances than the other models. The models using VNIR spectra were superior to those using NIR spectra. The overall results indicated that hyperspectral imaging with multi-task learning could predict the quality attributes of spinach simultaneously for spinach quality inspection under various storage conditions. This research will guide food quality inspection by simultaneously inspecting multiple quality attributes.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11152701 | PMC |
http://dx.doi.org/10.1016/j.fochx.2024.101481 | DOI Listing |
Polymers (Basel)
January 2025
Institute of Textile Auxiliary and Ecological Dyeing Finishing, Nanjing Tech University, 30 South Puzhu Road, Nanjing 211816, China.
A simple and non-chemical binding nanofiber (-CD/PA) adsorbent was obtained by electrospinning a mixture of -cyclodextrin (-CD) and polyacrylate (PA). The cationic dyes in wastewater were removed by the host-guest inclusion complex of the -cyclodextrin and the electrostatic interaction between the polyacrylate and the dyes groups. The influence of the content of -cyclodextrin on the surface morphology and adsorption capacity of the nanofiber membrane was discussed, and the optimized adsorption capacity of nanofiber adsorption material was determined.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Centre of Mechanical Technology and Automation (TEMA), Department of Mechanical Engineering, University of Aveiro, 3810-193 Aveiro, Portugal.
To automate the quality control of painted surfaces of heating devices, an automatic defect detection and classification system was developed by combining deflectometry and bright light-based illumination on the image acquisition, deep learning models for the classification of non-defective (OK) and defective (NOK) surfaces that fused dual-modal information at the decision level, and an online network for information dispatching and visualization. Three decision-making algorithms were tested for implementation: a new model built and trained from scratch and transfer learning of pre-trained networks (ResNet-50 and Inception V3). The results revealed that the two illumination modes employed widened the type of defects that could be identified with this system, while maintaining its lower computational complexity by performing multi-modal fusion at the decision level.
View Article and Find Full Text PDFSensors (Basel)
January 2025
State Key Laboratory of Marine Resource Utilization in South China Sea, School of Chemistry and Chemical Engineering, Hainan University, Haikou 570228, China.
The detection of highly toxic chemicals such as phosgene is crucial for addressing the severe threats to human health and public safety posed by terrorist attacks and industrial mishaps. However, timely and precise monitoring of phosgene at a low cost remains a significant challenge. This work is the first to report a novel fluorescent system based on the Intramolecular Charge Transfer (ICT) effect, which can rapidly detect phosgene in both solution and gas phases with high sensitivity by integrating a benzo[1,2-b:6,5-b']dithiophene-4,5-diamine (BDTA) probe.
View Article and Find Full Text PDFSensors (Basel)
January 2025
School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China.
The automated detection of yarn margins is crucial for ensuring the continuity and quality of production in textile workshops. Traditional methods rely on workers visually inspecting the yarn margin to determine the timing of replacement; these methods fail to provide real-time data and cannot meet the precise scheduling requirements of modern production. The complex environmental conditions in textile workshops, combined with the cylindrical shape and repetitive textural features of yarn bobbins, limit the application of traditional visual solutions.
View Article and Find Full Text PDFSensors (Basel)
January 2025
College of Science and Technology, Ningbo University, Ningbo 315000, China.
The quality of surface morphology can reflect the electrical performance of silver-based contacts. Existing research on the correlation of morphological-electrical performance is based solely on empirical models from traditional visual inspections and only considers the impact of visually observable macro-textural features on electrical performance. However, the influence of micro-textural features on electrical performance should not be overlooked.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!