As a typical carbon-based material electrode, graphene fiber exhibits many advantages, such as good electrical conductivity, lightweight, and strong structural designability. Its demand is increasing in the wearable display field. With the help of fine denier fiber spinning combined with multistranded graphene fibers prepared via twisting and drafting, their petal-like twisted structure endows the fibers with a high specific surface area, enabling them to complete dye adsorption within 30 min. Simultaneously, compared with that of a single fiber with the same thickness, the volume specific resistance of a multistranded twisted graphene fiber is reduced by 2.4 times. During force sensing, the twisted structure of multistranded fibers exhibits varying simultaneity of fiber fracture with excellent resistance sensitivity reaching up to 55%. The multistranded twisted flexible graphene fibers demonstrate excellent robustness. Electroluminescent flexible devices prepared with graphene fibers and fiber braided fabrics with different organizational structures as electrodes emit highly saturated short-wave blue light during long-term multiple use. Therefore, multistranded twisted graphene fibers exhibit considerable potential for future applications in wearable multicolor smart displays and flexible optical signal electronics.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/acsami.4c05111 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Large-Area Conductor-Loaded PDMS Flexible Composites for Wireless and Chipless Electromagnetic Multiplexed Temperature Sensors.
Adv Sci (Weinh)
January 2025
James Watt School of Engineering, University of Glasgow, Glasgow, G12 8QQ, UK.
Capacitive dielectric temperature sensors based on polydimethylsiloxane (PDMS) loaded with 10 vol% of inexpensive, commercially-available conductive fillers including copper, graphite, and milled carbon fiber (PDMS-CF) powders are reported. The sensors are tested in the range of 20-110 °C and from 0.5 to 200 MHz, with enhanced sensitivity from 20 to 60 °C, and a relative response of 85.
View Article and Find Full Text PDFCarbon Black Absorption Enhanced Fiber-Optic Photoacoustic Gas Sensing System with Ultrahigh Sensitivity.
Anal Chem
January 2025
School of Optoelectronic Engineering and Instrumentation Science, Dalian University of Technology, Dalian, Liaoning 116024, China.
A highly sensitive trace gas sensing system based on carbon black absorption enhanced photoacoustic (PA) spectroscopy (PAS) is reported. A carbon black sheet and a fiber-optic cantilever microphone (FOCM) are integrated to form a fiber-optic cantilever spectrophone (FOCS). The gas concentration is obtained by measuring the acoustic wave amplitude generated by the carbon black sheet, which absorbs the laser passing through the interest gas.
View Article and Find Full Text PDFPorous carbon nanosheets integrated with graphene-wrapped CoO and CoNx as efficient bifunctional oxygen electrocatalysts for rechargeable zinc-air batteries.
J Colloid Interface Sci
January 2025
CAS Key Laboratory of Carbon Materials, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001, China. Electronic address:
The development of advanced bifunctional oxygen electrocatalysts for the oxygen reduction reactions (ORR) and oxygen evolution reactions (OER) is crucial for the practical application of zinc-air batteries (ZABs). Herein, porous carbon nanosheets integrated with abundant graphene-wrapped CoO and CoNx (CoO/CoNx-C) were successfully fabricated through a simple one-step pyrolysis. With convenient porous channel and large accessible surface, abundant CoO/CoNx species and graphene wrapping structure, CoO/CoNx-C exhibited a half-wave potential of 0.
View Article and Find Full Text PDFEnhancing Polylactic Acid (PLA) Performance: A Review of Additives in Fused Deposition Modelling (FDM) Filaments.
Polymers (Basel)
January 2025
Materials Engineering and Welding Department, Transilvania University of Brasov, 500036 Brasov, Romania.
This review explores the impact of various additives on the mechanical properties of polylactic acid (PLA) filaments used in Fused Deposition Modeling (FDM) 3D printing. While PLA is favored for its biodegradability and ease of use, its inherent limitations in strength and heat resistance necessitate enhancements through additives. The impact of natural and synthetic fibers, inorganic particles, and nanomaterials on the mechanical properties, printability, and overall functionality of PLA composites was examined, indicating that fiber reinforcements, such as carbon and glass fibers, significantly enhance tensile strength and stiffness, while natural fibers contribute to sustainability but may compromise mechanical stability.
View Article and Find Full Text PDFFabrication and Performance Enhancement of Wood Liquefaction-Based Carbon Fibers Modified with Alumina Nanoparticles.
Polymers (Basel)
January 2025
College of Resources, Environment and Materials, Guangxi University, Nanning 530004, China.
In this paper, alumina-modified wood liquefaction (AL-WP) was prepared by blending nano-alumina (AlO) into wood liquefaction phenolic resin (WP) using a co-blending method. Alumina-modified wood liquefaction protofilament fiber (AL-WPF) was obtained by melt-spinning, curing, and thermo-curing processes, which were followed by carbonization to obtain alumina-modified wood liquefaction carbon fiber (AL-WCF). This paper focuses on the enhancement effect of nano-alumina doping on the mechanical properties and heat resistance of wood liquefaction carbon fiber (WCF), explores the evolution of graphite microcrystalline structure during the high-temperature carbonization process, and optimizes the curing conditions of AL-WPF.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!