Statement Of Problem: Evidence on the long-term clinical assessment and longevity of ceramic veneers bonded to different substrates is limited.
Purpose: The purpose of this systematic review and meta-analysis was to evaluate the effect of various substrates, including enamel, dentin, or an existing composite resin restoration, on the clinical survival and complication rates of ceramic veneers.
Material And Methods: The PubMed, Scopus, and the Cochrane Library electronic databases were searched, and related journals were hand searched without time or language restrictions to identify clinical trials that compared the survival rate and clinical complication rates when bonding ceramic veneers to different tooth substrates. The success rate of the included participants was estimated by the number of veneers that did not require a clinical intervention, and the survival rate by all veneers that did not fail absolutely. The risk difference (RD) with 95% confidence intervals (CIs) for dichotomous outcomes was used to quantify the intervention effect.
Results: Of 973 screened articles, 6 clinical studies were included. The survival and success rates varied depending on the bonding substrate. Enamel-bonded veneers had almost perfect rates of survival (99% with a range of 98% to 100%) and success (99% with a range of 98% to 100%). Veneers bonded to composite resin or surfaces with minimal dentin exposure had slightly lower survival rates (94% with a range of 91% to 97% and 95% with a range of 91% to 100%, respectively) and success rates (70% with a range of 60% to 80% and 95% with a range of 90% to 99%). Severe dentin exposure significantly decreased both survival rates (91% with a range of 84% to 98%) and success rates (74% with a range of 64% to 85%). The combined findings suggested that ceramic veneers bonded to enamel had fewer clinical complications (RD: -0.04; 95% CI: -0.09 to 0.02) and lower failure rates (RD: -0.13; 95% CI: -0.32 to 0.07) compared with those bonded to exposed dentin. Additionally, veneers attached to teeth with minimal dentin exposure were significantly less likely to require clinical interventions (RD: -0.16; 95% CI: -0.31 to -0.01) and had a reduced incidence of failure (RD: -0.08; 95% CI: -0.17 to 0.01) compared with those with severe dentin exposure.
Conclusions: Ceramic veneers bonded to enamel showed higher survival and success rates with lower clinical incidences of complications and failure than those bonded to dentin or teeth with existing composite resin restorations.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.prosdent.2024.03.019 | DOI Listing |
BMC Oral Health
January 2025
Nanjing Stomatological Hospital, Affiliated Hospital of Medical School, Institute of Stomatology, Nanjing University, Nanjing, China.
Objectives: To compare the stress distribution and crack propagation in cracked mandibular first molar restored with onlay, overlay, and two types of occlusal veneers using two different CAD/CAM materials by Finite Element Analysis (FEA).
Materials And Methods: A mandibular first molar was digitized using a micro CT scanning system in 2023. Three-dimensional dynamic scan data were transformed, and a 3D model of a cracked tooth was generated.
Dent Mater
January 2025
Department of Biomaterials, School of Dentistry, University of São Paulo, Sao Paulo, Brazil.
Objective: To analyze the impact of the translucency/opacity of two commercial brands of resin cements and different translucency of lithium disilicate on the masking ability of saturated substrates.
Methods: 120 samples (n = 5) were prepared using 0.5 mm lithium disilicate (IPS e.
J Esthet Restor Dent
January 2025
Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany.
Objective: Investigation of the mechanical properties of occlusal veneers made from zirconia with varying translucency, bonded to different tooth substrates.
Materials And Methods: Sixty-four extracted molars were divided into two groups: preparation within enamel (E) or extending into dentin (D). Veneers were milled from four zirconia ceramics (n = 8): 5Y-TZP (HT), a multilayer of 5 and 3Y-TZP (GT), 3Y-TZP (LT), and 4Y-TZP (MT).
Oper Dent
January 2025
Nathaniel C Lawson, DDS, PhD, director of Master of Science in Dental Biomaterials program and associate professor, Department of Clinical and Community Sciences, University of Alabama at Birmingham School of Dentistry, Birmingham, AL, USA.
Objective: This study aimed to assess the fracture resistance of chairside computer assisted design and computer assisted manufacturing (CAD-CAM) lithium disilicate partial and full-coverage crowns and veneers for maxillary canines.
Methods And Materials: Forty-eight restorations for maxillary right canines (12 per group) were designed as follows: (1) partial crown with finish line in the upper middle third; (2) partial crown with finish line in the lower middle third; (3) traditional labial veneer; and (4) traditional full-coverage crown. Restorations were fabricated out of lithium disilicate (Amber Mill, Hassbio) using a chairside CAD-CAM system (Cerec Dentsply Sirona).
J Vis Exp
December 2024
School of Engineering and Materials Science, Queen Mary University of London.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!