Within the burgeoning field of electronic materials, B-N Lewis acid-base pairs, distinguished by their partial charge distribution across boron and nitrogen centers, represent an underexplored class with significant potential. These materials exhibit inherent dipoles and are excellent candidates for ferroelectricity. However, the challenge lies in achieving the optimal combination of hard-soft acid-base pairs to yield B-N adducts with stable dipoles. Herein, we present an enantiomeric pair of B-N adducts [CHCH(CH)NHBF] (MBA-BF) crystallizing in the polar monoclinic P2 space group. The ferroelectric measurements on MBA-BF gave a rectangular P-E hysteresis loop with a remnant polarization of 7.65 μC cm, a value that aligns with the polarization derived from the extensive density-functional theory computations. The PFM studies on the drop-casted film of MBA-BF further corroborate the existence of ferroelectric domains, displaying characteristic amplitude-bias butterfly and phase-bias hysteresis loops. The piezoelectric nature of the MBA-BF was confirmed by its direct piezoelectric coefficient (d) value of 3.5 pC N for its pellet. The piezoelectric energy harvesting applications on the sandwich devices fabricated from the as-made crystals of MBA-BF gave an open circuit voltage (V) of 6.2 V. This work thus underscores the untapped potential of B-N adducts in the field of piezoelectric energy harvesting.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1002/anie.202400366 | DOI Listing |
Biomacromolecules
January 2025
Department of Material Engineering, Indian Institute of Science, Bangalore 560012, Karnataka, India.
Chitosan (CHT) is a known piezoelectric biomacromolecule; however, its usage is limited due to rapid degradation in an aqueous system. Herein, we prepared CHT film via a solvent casting method and cross-linked in an alkaline solution. Sodium hydroxide facilitated deprotonation, leading to increased intramolecular hydrogen bonding and mechanical properties.
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083, China.
Porous piezoelectric materials have attracted much interest in the fields of sensing and energy harvesting owing to their low dielectric constant, high piezoelectric voltage coefficient, and energy harvesting figure of merit. However, the introduction of porosity can decrease the piezoelectric coefficient, which restricts the enhancement of output current and power density. Herein, to overcome these challenges, an array-structured piezoelectric composite energy harvester with aligned porosity was constructed via a dual structure design strategy to enhance the output current and power density.
View Article and Find Full Text PDFPorous structures offer several key advantages in energy harvesting, making them highly effective for enhancing the performance of piezoelectric and triboelectric nanogenerators (PENG and TENG). Their high surface area-to-volume ratio improves charge accumulation and electrostatic induction, which are critical for efficient energy conversion. Additionally, their lightweight and flexible nature allows for easy integration into wearable and flexible electronics.
View Article and Find Full Text PDFPhys Chem Chem Phys
January 2025
Institute for Computational Materials Science, Joint Center for Theoretical Physics, and Key Laboratory for High Efficiency Energy Conversion Science and Technology of Henan Province, School of Physics and Electronics, Henan University, Kaifeng 475004, China.
Two-dimensional (2D) materials have attracted enormous research attention due to their remarkable properties and potential applications in electronic and optoelectronic devices. In this work, Janus 2D copper-containing chalcogenides, CuPSeS and CuPTeSe monolayers, are proposed and studied systematically based on first-principles calculations. These two Janus-structured materials possess the same thermal and dynamic stability as the perfect CuPSe structure.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Portici Research Centre, ENEA-Italian National Agency for New Technologies, Energy and Sustainable Economic Development, 80055 Portici, Italy.
Polyvinylidene fluoride (PVDF)-based materials are the most researched polymers in the field of energy harvesting. Their production in thin-film form through printing technologies can potentially offer several manufacturing and performance advantages, such as low-cost, low-temperature processing, use of flexible substrates, custom design, low thermal inertia and surface-scaling performance. However, solution-based processes, like printing, miss fine control of the microstructure during film-forming, making it difficult to achieve a high level of polarization, necessary for PVDF to exhibit electroactive characteristics.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!