We reported here on the fabrication and characterization of a smart titanium alloy bolt based on a high-frequency piezoelectric thin-film sensor. The thin-film sensor was directly deposited on a titanium alloy bolt head with radio frequency magnetron sputtering and characterized by a scanning electron microscope and an atomic force microscope. The ultrasonic characteristics of the smart bolt, which include a pure and broad frequency spectrum peaked at 14.81 MHz, high measurement accuracy below 3%, and high repeatability free from some interference from bolt detection position change, were fully characterized. No obvious frequency shift was observed with the increase in axial preload. Based on the mono-wave method [TOF (time of flight) of longitudinal mode wave], TOF change increased linearly with preload force in the range of 0-20 kN. With the increase in temperature from 22 to 150 °C, the TOF linearly increases while the longitudinal wave velocity linearly decreases. The results indicate the prepared smart titanium alloy bolt is suitable as a smart aviation and automotive fastener.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1063/5.0183274 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Enhancing Rotator Cuff Repair in Rabbit Osteoporosis With Chitosan Quaternary Ammonium Salt-Coated Nickel-Titanium Memory Alloy Anchors.
Am J Sports Med
January 2025
Department of Orthopaedics, Lanzhou University Second Hospital, Lanzhou, Gansu, P.R. China.
Background: For patients with osteoporosis and rotator cuff tears, there is still no consensus on current treatment methods. The material, structure, and number of anchors have important effects on the repair outcome.
Purpose: To investigate the use of chitosan quaternary ammonium salt-coated nickel-titanium memory alloy (NTMA) anchors to treat rotator cuff injury in shoulders with osteoporosis in a rabbit osteoporosis model.
Comparison of the pull-out force of different microtube-based methods in fractured endodontic instrument removal: An in-vitro study.
BMC Oral Health
January 2025
Department of Endodontics, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.
Background: The fracture of an endodontic instrument within the root canal system can occur during root canal therapy, complicating thorough cleaning and shaping. Consequently, managing the broken fragment becomes crucial.
Methods: Eighty Nickel-titanium (NiTi) #20 K-files (Mani, Tochigi, Japan) were cut 8 mm from the tip, fixed into a corkboard, and classified into five groups (n = 14 each).
Effect of cobalt ions doping on morphology and electrochemical properties of hydroxyapatite coatings for biomedical applications.
Sci Rep
January 2025
Department of Physical Chemistry, Faculty of Chemistry, University of Tabriz, 29 Bahman Blvd., Tabriz, Iran.
Hydroxyapatite (HA) is an engineered biomaterial that closely resembles the hard tissue composition of humans. Biological HA is commonly non-stoichiometric and features lower crystallinity and higher solubility than stoichiometric HA. The chemical compositions of these biomaterials include calcium (Ca), phosphorus (P), and trace amounts of various ions such as magnesium (Mg), zinc (Zn), and strontium (Sr).
View Article and Find Full Text PDFExpression of beam hardening artifacts on horizontally stitched cone-beam computed tomography images.
Imaging Sci Dent
December 2024
Department of Oral Diagnosis, Division of Oral Radiology, Piracicaba Dental School, University of Campinas, Piracicaba, SP, Brazil.
Purpose: This study was performed to evaluate the expression of beam hardening artifacts generated by high atomic number materials in stitched cone-beam computed tomography (CBCT) images, compared to the traditional acquisition mode.
Materials And Methods: CBCT volumes were acquired using an acrylic resin phantom embedded with pairs of cylinders made from amalgam dental alloy, cobalt-chromium alloy, gutta-percha, titanium, and zirconium. These cylinders were placed within the overlapping zones of the stitching reconstruction area.
Electrophoretic Deposition of Gentamicin Into Titania Nanotubes Prevents Evidence of Infection in a Mouse Model of Periprosthetic Joint Infection.
J Orthop Res
December 2024
Department of Orthopedic Surgery, Rush University Medical Center, Chicago, Illinois, USA.
Periprosthetic joint infection (PJI) is a leading cause and major complication of joint replacement failure. As opposed to standard-of-care systemic antibiotic prophylaxis for PJI, we developed and tested titanium femoral intramedullary implants with titania nanotubes (TNTs) coated with the antibiotic gentamicin and slow-release agent chitosan through electrophoretic deposition (EPD) in a mouse model of PJI. We hypothesized that these implants would enable local gentamicin delivery to the implant surface and surgical site, effectively preventing bacterial colonization.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!