Background: This study aimed to evaluate the effect of Silver Diamine Fluoride (SDF) on the microleakage of flowable resin composite (FRC) and resin-modified glass ionomer cement (GIC) restorations bound to carious primary dentin.

Methods: Forty-four extracted carious primary molars were allocated into four groups as follows (n = 11 teeth/group): Group I, Flowable resin composite (FRCa): SDF38% treatment + FRC, Group II, Flowable resin composite (FRCb): FRC without SDF treatment, Group III, Resin-modified glass ionomer cement (GICa): SDF38% treatment + GIC, Group IV, Resin-modified glass ionomer cement (GICb): GIC without SDF treatment. Specimens were subjected to thermo cycling at 500 cycles between 5 to 55 °C (dwell time of 60 seconds) in baths before being immersed for 24 h in a 1% toluidine blue solution. Microleakage testing was conducted for each specimen in two areas; occlusal and gingival. Specimens were evaluated under stereomicroscope at 4x magnification. Results were analyzed using Kruskal-Wallis test followed by pairwise comparisons utilizing Dunn's post hoc test at p ≤ 0.05.

Results: Insignificant differences between different groups (p = 0.49) were observed at the gingival walls area readings. The highest value was found in GICb (2.33 ± 0.52), while the lowest value was found in FRCa (1.71 ± 0.76). Insignificant differences between different groups (p = 0.982) were observed at the occlusal walls area readings. The highest value was found in FRCa (1.43 ± 0.98), while the lowest value was found in GICb (1.17 ± 1.33).

Conclusion: SDF does not adversely affect the microleakage of FRC and GIC restorations bound to carious primary dentin.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10792808PMC
http://dx.doi.org/10.1186/s12903-024-03861-2DOI Listing

Publication Analysis

Top Keywords

flowable resin
16
resin composite
16
glass ionomer
16
ionomer cement
16
carious primary
16
resin-modified glass
12
silver diamine
8
diamine fluoride
8
microleakage flowable
8
primary dentin
8

Similar Publications

Dental ultrasonic scalers are commonly employed in periodontal treatment; however, their ability to roughen tooth surfaces is a worry since roughness may increase plaque production, a key cause of periodontal disease. This research studied the influence of a piezoelectric ultrasonic scaler on the roughness of two distinct flowable composite filling materials. To do this, 10 disc-shaped samples were generated from each of the two flowable composite materials.

View Article and Find Full Text PDF

3-Dimensional topographic enamel surface changes after different debonding techniques for aligner attachments: a micro-CT study.

Clin Oral Investig

January 2025

Faculty of Dentistry, Department of Orthodontics , Hacettepe University, Sihhiye, Ankara, 06100, Turkey.

Introduction: To evaluate topographic changes of enamel surface in 3-dimensional after different debonding methods of aligner attachments formed with 2 different composite resins.

Methods: Vertical rectangular attachments were created on 88 premolar teeth and divided into two composite resin groups (Group 1:flowable, Group 2:packable) (N = 44). These were then divided into two subgroups (N = 22) using different debonding methods.

View Article and Find Full Text PDF

Does the Type of Resin Luting Material Affect the Bonding of CAD/CAM Materials to Dentin?

Dent J (Basel)

January 2025

Department of Restorative Dentistry, Faculty of Dentistry, Yeditepe University, İstanbul 34728, Turkey.

This study aimed to investigate the microtensile bond strength (µTBS) of composite-based (Cerasmart), polymer-infiltrated (Vita Enamic), and feldspathic (Cerec) CAD/CAM blocks luted to dentin using a dual-cure resin cement (LinkForce), as well as micro-hybrid (G-aenial) and flowable composites (G-aenial Universal Flo), and evaluate the microhardness (HV) of luting materials through the CAD/CAM blocks. Cerasmart, Enamic, and Cerec were luted to dentin using three luting materials; LinkForce, G-aenial, and Universal Flo (n = 5). For HV, 117 disk-shaped specimens from LinkForce, G-aenial, and Universal Flo (n = 13) were polymerized through 3 mm thick CAD/CAM.

View Article and Find Full Text PDF

The Influence of Posterior Class II Composite Restoration Location and Techniques on Marginal Sealing.

Dent J (Basel)

January 2025

Department of Oral Rehabilitation, The Maurice and Gabriela Goldschleger School of Dental Medicine, Faculty of Medicine, Tel Aviv University, Tel Aviv 6997801, Israel.

: The success of treatment and prevention for secondary caries hinges significantly on the techniques employed in Class II composite restoration. Additionally, the location of the restored tooth within the oral cavity has emerged as a potential factor determining the quality of the restoration. A comprehensive understanding of these interrelated variables is crucial for advancing the efficacy and durability of dental composite restorations.

View Article and Find Full Text PDF

The injection moulding technique (IMT) is a minimally invasive restorative treatment. This technique enables the application of thin, flowable composite layers into a stable, transparent silicone index that serves as a mould. Due to the fluid properties of the composite, it efficiently fills the silicone tray and seamlessly integrates with the tooth structure, often obviating tooth preparation and preserving overall tooth integrity.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!