This study delves into the intricacies of ultraprecision machining, particularly in the context of machining optical freeform surfaces using Diamond Turning Machines (DTMs). It underscores the dynamic relationship between toolpath generation, hydrostatic bearing in DTMs, and the machining process. Central to this research is the innovative introduction of Metal Matrix Composites (MMCs) to replace the traditional materials used in designing linear bearings. This strategic substitution aims to dynamically enhance both the accuracy and the quality of the machined optical freeform surfaces. The study employs simulation-based analysis using ADAMS to investigate the interfacial cutting forces at the tooltip and workpiece surface and their impacts on the machining process. Through simulations of STS mode ultraprecision machining, the interfacial cutting forces and their relationship with changes in surface curvatures are examined. The results demonstrate that the use of MMC material leads to a significant reduction in toolpath pressure, highlighting the potential benefits of employing lightweight materials in improving the dynamic performance of the system. Additionally, the analysis of slideway joints reveals the direct influence of interfacial cutting forces on the linear slideways, emphasising the importance of understanding and controlling these forces for achieving higher-precision positioning and motion control. The comparative analysis between steel and MMC materials provides valuable insights into the effects of material properties on the system's dynamic performance. These findings contribute to the existing body of knowledge and suggest a potential shift towards more advanced precision forms, possibly extending to pico-engineering in future systems. Ultimately, this research establishes a new standard in the field, emphasising the importance of system dynamics and interfacial forces in the evolution of precision manufacturing technologies.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10745667 | PMC |
| http://dx.doi.org/10.3390/mi14122228 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Understanding the Dynamics of Sulfur Droplets Formation in Lean-Electrolyte and Low-Temperature Lithium-Sulfur Batteries.
Adv Sci (Weinh)
December 2024
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Hong Kong, 999077, P. R. China.
Article Synopsis
- Lithium-sulfur batteries (LSBs) are promising next-gen rechargeable batteries thanks to their high energy density and low-cost sulfur cathodes, but they face challenges with insulation of sulfur particles at low temperatures.
- The study focuses on the generation of liquid sulfur droplets in LSBs and reveals that their formation during the polysulfide oxidation reaction is consistent across various electrolyte/sulfur (E/S) ratios and temperatures.
- Findings suggest that the sulfur oxidation reaction exhibits pseudo-zero-order kinetics and specific reaction constants that vary with E/S ratios, showing that liquid sulfur can be maintained even in extreme conditions like -20 °C.
Development of a High-Speed Precision Ultrasonic-Assisted Spindle for Ultra-Precision Optical Mold Machining.
Sensors (Basel)
November 2024
College of Mechanical and Vehicle Engineering, Hunan University, Changsha 410082, China.
Ultrasonic vibration-assisted grinding is a critical method for machining ultra-hard optical molds. However, current ultrasonic-assisted grinding spindles, as essential foundational equipment, face limitations in maintaining ultra-high rotational speed, high precision, and a compact structure during ultrasonic operation. This study presents a novel ultra-precision ultrasonic-assisted high-speed aerostatic spindle for grinding ultra-hard optical molds, developed through theoretical calculations, FEM, and CFD simulations.
View Article and Find Full Text PDFMiniature optical fiber photoacoustic spectroscopy gas sensor based on a 3D micro-printed planar-spiral spring optomechanical resonator.
Photoacoustics
December 2024
Photonics Research Institute, Department of Electrical and Electronic Engineering, The Hong Kong Polytechnic University, Kowloon, Hong Kong SAR.
Article Synopsis
- Photoacoustic spectroscopy (PAS) gas sensors using optomechanical resonators (OMRs) are gaining popularity for extremely sensitive gas detection but face challenges in size and performance balance for compact applications.
- A new miniature PAS gas sensor, featuring a planar-spiral spring OMR micro-printed on a fiber-optic ferrule, showcases enhanced acoustic sensitivity and can detect CH gas concentrations as low as 45 parts per billion.
- With a rapid response time of about 0.2 seconds, this innovative optical fiber OMR-PAS gas sensor is promising for applications in production control and environmental monitoring.
Investigation on the Machinability of Polycrystalline ZnS by Micro-Laser-Assisted Diamond Cutting.
Micromachines (Basel)
October 2024
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.
Article Synopsis
- Polycrystalline ZnS is a key infrared optical material known for its excellent optical properties but is challenging to machine due to its soft and brittle nature.
- Recent advancements in in situ laser-assisted diamond cutting have shown to enhance the ultra-precision machining of ZnS by improving its ductile characteristics and reducing microhardness.
- Experimental results demonstrate that this method significantly improves cutting quality, achieving a 73.58% better surface finish and changing the damage patterns during machining, thus providing a valuable approach for high-performance optical systems.
Research on the Magnetorheological Finishing Technology of a High-Steepness Optical Element Based on the Virtual-Axis and Spiral Scanning Path.
Micromachines (Basel)
September 2024
College of Intelligent Science and Technology, National University of Defense Technology, Changsha 410073, China.
Magnetorheological finishing (MRF) of aspherical optical elements usually requires the coordination between the translational axes and the oscillating axes of the machine tool to realize the processing. For aspheric optical elements whose steepness exceeds the machining stroke of the equipment, there is still no better method to achieve high-precision and high-efficiency error convergence. To solve this problem, an MRF method combining virtual-axis technology and a spiral scanning path is proposed in this paper.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!