This study aimed to evaluate and compare the effects of oil- and air-heat treatments on the durability of Paulownia tomentosa and Pinus koraiensis woods against Fomitopsis palustris and Trametes versicolor. The wood samples were treated in palm oil and air at 180, 200, and 220 °C for 2 h. The weight loss, morphology, crystalline properties, and chemical compounds of untreated and heat-treated wood after fungal attack were investigated. The significant difference in weight loss between oil- and air-heat-treated samples was shown at 220 °C. Heat-treated wood exposed to white-rot fungus showed a lower weight loss than that exposed to brown-rot fungus. The cell components in the untreated- and heat-treated Paulownia tomentosa and Pinus koraiensis at 180 °C were severely damaged due to fungal exposure compared to those at 220 °C. A fungal effect on the relative crystallinity was observed in heat-treated wood at 180 °C, whereas the effect was not observed at 220 °C. Following brown-rot fungus exposure, untreated- and heat-treated wood at 180 °C showed a notable change in the Fourier transform infrared (FTIR) peaks of polysaccharides, whereas no noticeable change in lignin peaks was observed. Heat-treated wood at 220 °C showed no noticeable change in the FTIR spectra owing to brown-rot fungus exposure. Exposure to white-rot fungus did not noticeably change the FTIR spectra of untreated and heat-treated wood.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10713529 | PMC |
http://dx.doi.org/10.1038/s41598-023-48971-z | DOI Listing |
Spectrochim Acta A Mol Biomol Spectrosc
November 2024
University Department, Royal Naval School of Marine Engineering - Boulevard Sour Jdid Casablanca, Morocco.
This study describes the effect of heat treatment on some physical, chemical, and mechanical properties of Eucalyptus Camaldulensis (EC) wood at different temperatures and treatment times (200 °C-260 °C for 5, 60, and 90 min). The evaluation of hygroscopic properties was determined by relative humidity, mass loss, dimensional stability tests, and density. The results showed that the heat treatment leads to an increase in mass loss of 5.
View Article and Find Full Text PDFPolymers (Basel)
June 2024
Research Center for Biomass and Bioproducts, National Research and Innovation Agency, Cibinong 16911, Indonesia.
This study aimed to analyze the effect of pre-heat treatment on bamboo strand properties and its impact on the properties of the resulting bamboo-oriented strand board (BOSB). Giant bamboo ( (Schult.) Backer) with a density of 0.
View Article and Find Full Text PDFPolymers (Basel)
February 2024
Department of Wood Technology, Faculty of Forestry and Wood Technology, University of Zagreb, 10000 Zagreb, Croatia.
In this research, the influence of titanium dioxide (TiO) nanoparticles and their modifications on the weathering resistance of untreated and heat-treated wood was studied. The wood samples were coated with polyacrylate waterborne emulsion coatings that contain nano-TiO in the amount of 0.75 wt.
View Article and Find Full Text PDFPolymers (Basel)
January 2024
Department of Forestry, National Chung Hsing University, Taichung 402, Taiwan.
Wood fibers (WFs) were treated at a fixed heat temperature (180 °C) for 2-6 h and added to a polylactic acid (PLA) matrix to produce wood-PLA composite (WPC) filaments. Additionally, the effects of the heat-treated WFs on the physicomechanical properties and impact strength of the WPC filaments and 3D-printed WPC parts using fused filament fabrication (FFF) were examined. The results revealed that heat-treated WFs caused an increase in crystallinity and a significant reduction in the number of pores on the failure cross section of the WPC filament, resulting in a higher tensile modulus and lower elongation at break.
View Article and Find Full Text PDFSci Total Environ
March 2024
State Key Laboratory of Efficient Production of Forest Resources, Beijing Key Laboratory of Wood Science and Engineering, MOE Key Laboratory of Wooden Material Science and Application, College of Material Science and Technology, Beijing Forestry University, Beijing 100083, PR China. Electronic address:
Bamboo heat treatment will cause plenty of release of volatile organic compounds (VOCs) into the atmosphere which are important precursors for ozone (O) formation. In this study, dewaxed bamboo was heat-treated at 180 °C for 2 h to investigate the emission characteristics and the formation pathways of VOCs during heat treatment by removing different main components. The results showed that aldehydes (22.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!