Multijunction solar cells provide a path to overcome the efficiency limits of standard silicon solar cells by harvesting a broader range of the solar spectrum more efficiently. However, Si-based multijunction architectures are hindered by incomplete harvesting in the near-infrared (near-IR) spectral range as Si subcells have weak absorption close to the band gap. Here, we introduce an integrated near-field/far-field light trapping scheme to enhance the efficiency of silicon-based multijunction solar cells in the near-IR range. To achieve this, we design a nanopatterned diffractive silver back-reflector featuring a scattering matrix that optimizes trapping of multiply scattered light into a range of diffraction angles. We minimize reflection to the zeroth order and parasitic plasmonic absorption in silver by engineering destructive interference in the patterned back-contact. Numerical and experimental assessment of the optimal design on the performance of single-junction Si TOPCon solar cells highlights an improved external quantum efficiency over a planar back-reflector (+1.52 mA/cm). Nanopatterned metagrating back-reflectors are fabricated on GaInP/GaInAsP//Si two-terminal triple-junction solar cells via substrate conformal imprint lithography and characterized optically and electronically, demonstrating a power conversion efficiency improvement of +0.9% over the planar reference. Overall, our work demonstrates the potential of nanophotonic light trapping for enhancing the efficiency of silicon-based multijunction solar cells, paving the way for more efficient and sustainable solar energy technologies.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10655497 | PMC |
http://dx.doi.org/10.1021/acsphotonics.3c01124 | DOI Listing |
ACS Appl Mater Interfaces
December 2024
Department of Flexible Sensing Technology, Institute of Chemical Engineering, Guangdong Academy of Sciences, Guangzhou 510665, China.
The global solar market is booming with a rapid growth in installed integrated devices, while photovoltaic (PV) systems are suffering from waste heat, which causes the decline of the photovoltaic conversion efficiency (PCE). This study presents the seamless integration of the ionic thermoelectric generator (iTEG) layer with traditional PV modules, facilitating the exploitation of waste heat and augmenting the overall power output. Experimental results validate the effectiveness of the iTEG, demonstrating substantial power generation and a consistent energy output.
View Article and Find Full Text PDFJ Colloid Interface Sci
December 2024
Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei Key Laboratory of Polymer Materials, Hubei University, Wuhan 430062, China; State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China. Electronic address:
As the proportion of solar energy in the global energy mix increases, photovoltaic cells have emerged as one of the fastest-growing technologies in the renewable energy sector. However, photovoltaics utilize only a limited portion of the incident solar spectrum, resulting in significant amounts of light energy being wasted as heat. This excess heat raises the surface temperature of photovoltaic cells, which in turn reduces their overall efficiency.
View Article and Find Full Text PDFInorg Chem
December 2024
Laboratory of Complex Heterostructures and Multifunctional Materials, National Institute of Materials Physics, Atomistilor 405A, Magurele 077125, Romania.
CuZnSnSe (CZTSe) is a promising material for thin-film solar cells due to its suitable band gap, high absorption coefficient, and composition of earth-abundant and nontoxic elements. In this study, we prepared CZTSe thin films from Cu/SnSe and ZnSe stacks using a two-step annealing process. Initially, Cu-Sn-Se (CTSe) films were synthesized by sequential deposition and annealing of Cu and SnSe precursors in either a selenium (Se) or tin-selenium (Sn+Se) atmosphere.
View Article and Find Full Text PDFSmall
December 2024
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, School of New Energy, North China Electric Power University, Beijing, 102206, China.
Incorporating chlorine into the SnO electron transport layer (ETL) has proven effective in enhancing the interfacial contact between SnO and perovskite in perovskite solar cells (PSCs). However, previous studies have primarily focused on the role of chlorine in passivating surface trap defects in SnO, without considering its influence on the buried interface. Here, hydrochloric acid (HCl) is introduced as a chlorine source into commercial SnO to form Cl-capped SnO (Cl-SnO) ETL, aiming to optimize the buried interface of the PSC.
View Article and Find Full Text PDFAngew Chem Int Ed Engl
December 2024
Nankai University, Colege of Chemistry, CHINA.
Organic photovoltaic materials that can be processed via non-halogenated solvents are crucial for the large-area manufacturing of organic solar cells (OSCs). However, the limited available of electron acceptors with adequate solubility and favorable molecular packing presents a challenge in achieving efficient non-halogenated solvent-processed OSCs. Herein, inspired by the three-dimensional dimeric acceptor CH8-4, we employed a molecular isomerization strategy to synthesize its isomers, CH8-4A and CH8-4B, by tuning the position of fluorine (F) atom in the central unit.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!