For exploring advanced Zn-ion batteries (ZIBs) with long lifespan and high Coulombic efficiency (CE), the critically important point is to limit the undesired Zn dendrite and parasitic reactions. Among the coating for electrode is a promising strategy, relying on the trade-off between its thickness and stability to achieve the ultra-stable Zn anodes in ZIBs. Herein, a submicron-thick (≈0.4 µm) zincophilic CrN coatings are fabricated by a facile and industry-compatible magnetron sputtering approach. It is exhilarating that the ultrathin and dense CrN coatings with strong adsorption ability for Zn exhibit an impressive lifespan up to 3700 h with ≈100% CE at 1 mA cm. Along with the experiments and theoretical calculations, it is verified that the introduced CrN coatings cannot only effectively suppress the dendrite growth and notorious parasitic reactions, but also allow the uniform Zn deposition due to the reduced nucleation energy. Moreover, the as-assembled Zn@CrN‖MnO full cell delivers a high specific capacity of 171.1 mAh g after 1000 cycles at 1 A g, much better than that of Zn‖MnO analog (97.8 mAh g). This work provides a facile strategy for scalable fabrication of ultrathin zincophilic coating to push forward the practical applications of ZIBs.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1002/smll.202308818 | DOI Listing |
Materials (Basel)
January 2025
Centrum Výzkumu Řež s.r.o., Hlavní 130, 250 68 Husinec-Řež, Czech Republic.
Fuel failure caused by fretting damage to cladding remains a relevant issue despite decades of research and development aimed at enhancing the physical parameters of fuel. This paper presents the results of experiments conducted at the Research Centre Řež on Zr-1%Nb alloy tube specimens covered with protective coatings made of chromium (Cr) and nitrogen (N) compounds. The experiments involved debris-fretting tests under dry conditions at room temperature as well as microscopic measurements of groove depths.
View Article and Find Full Text PDFACS Appl Mater Interfaces
November 2024
Key Laboratory of Beam Technology of the Ministry of Education, School of Physics and Astronomy, Beijing Normal University, Beijing 100875, China.
Pharm Dev Technol
November 2024
Department of Chemical and Biotechnological Engineering, Université de Sherbrooke, Sherbrooke, QC, Canada.
Materials (Basel)
September 2024
Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Hydropower Department, Fiszera 14 St., 80-231 Gdansk, Poland.
The erosion process of a 4 μm monolayer CrN coating deposited on 316L stainless steel due to cavitation was investigated using finite element analysis (FEA). To estimate load parameters from cavitation pit geometry resulting from high impact velocity and high strain rate, the explicit dynamic solver was employed. Water microjet impacts at velocities of 100, 200 and 500 m/s were simulated to recreate different cavitation erosion intensities observed in the experiment.
View Article and Find Full Text PDFMaterials (Basel)
August 2024
McMaster Manufacturing Research Institute (MMRI), Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, ON L8S 4L7, Canada.
This study aims to optimize the performance of CrN coatings deposited on WC cutting tools for machining Ti6Al4V alloy, where the formation of built-up edge (BUE) is a prevalent and critical issue. In-house CrN coatings were developed using the PVD (Physical Vapor Deposition) process, with variations in deposition parameters including nitrogen gas pressure, bias voltage, and coating thickness. A comprehensive experimental approach encompassing deposition, characterization, and machining performance evaluation was employed to identify the optimal deposition conditions.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!