In this study, the efficacy of ionomers and poly-lactic acid (PLA) as an alternative solid material combined with scFv antibodies specific to bovine Y-sperm (Y-scFv) was studied to create a novel method of sexing technology. The coupling efficiency of Y-scFv to the surface of PLA, Na and Zn ionomer film was between 2 and 8 mg/mL. Fourier transform infrared spectra confirm that Y-scFv was bound with a carboxylic acid group in each film. Therefore, Na, Zn ionomers and PLA films conjugated with 4 and 8 mg/mL Y-scFv showed the highest concentration of Y-sperm in the eluted fraction. Considering that the elute fraction was enriched Y-sperm fraction, it contained 67.70-77.94 % of the Y-sperm ratio related to the produced supernatant fraction, which contained up to 69.31-76.01 % enriched X-sperm. In addition, the sperm quality after the sexing process was analyzed by CASA and imaging flow cytometry, which showed that each polymer did not have a negative effect on sperm motility and acrosome integrity for X-sperm. The capacity of ionomer and PLA combined with Y-scFv are used for bovine sperm sexing.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.ijbiomac.2023.128425 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Investigation of the Thermal Stability and Hydrolytic Degradation Kinetics of Poly(Lactide-co-Glycolide) Melts.
AAPS PharmSciTech
January 2025
Molecular Pharmaceutics and Drug Delivery, College of Pharmacy, The University of Texas at Austin, Austin, Texas, USA.
Poly(lactide-co-glycolide) (PLGA) is widely used in a variety of long-acting injectables. However, its biodegradable nature creates potential chemical stability challenges during melt extrusion, where PLGA is exposed to elevated temperature (100-140 °C) for several minutes. This study evaluated the thermal stability of three PLGA grades (Resomer® 502, 502H, and 505) with varying molecular weights and chain-ends using a differential scanning calorimeter and twin-screw extruder.
View Article and Find Full Text PDFAdditively manufactured ready-to-use platform using conductive recycled PLA for ketamine sensing.
Mikrochim Acta
January 2025
Federal University of Uberlândia, Chemistry Institute, Uberlândia, MG, 38400-902, Brazil.
The use of 3D-printed electrodes is reported fabricated from in-house conductive filament composed of a mixture of recycled poly (lactic acid) (rPLA), graphite (Gpt), and carbon black (CB) for fast detection of the abused drug ketamine. Firstly, the performance of these electrodes was evaluated in comparison to 3D-printed electrodes produced employing a commercially available conductive filament. After a simple pretreatment step (mechanical polishing), the new 3D-printed electrodes presented better performance than the electrodes produced from commercial filament in relation to peak-to-peak separation of the redox probe [Fe(CN)]/ (130 mV and 759 mV, respectively), charge transfer resistance (R = 1.
View Article and Find Full Text PDFpH-induced synergistic changes in color and shape of soft actuator based on degradable carbon dots/sodium alginate gel.
Carbohydr Polym
March 2025
College of Chemistry, Zhengzhou University, Zhengzhou 450000, China. Electronic address:
Soft actuators for intelligent robots require further elaboration to improve their biomedical applicability, which has led to the development of a series of flexible stimulus-responsive materials. However, fabricating degradable soft actuators that exhibit synergistic color and shape changes in response to environmental stimuli remains challenging. Here, we developed a soft actuating gel based on carbon dots (CDs) that are chemically cross-linked with sodium alginate.
View Article and Find Full Text PDFAdapting single-walled carbon nanotube-based thin-film transistors to flexible substrates with electrolyte-gated configurations using a versatile tri-layer polymer dielectric.
Nanoscale Adv
December 2024
Department of Chemical and Biological Engineering, University of Ottawa 161 Louis Pasteur Ottawa Ontario K1N 6N5 Canada
Flexibility has been a key selling point in the development of carbon-based electronics and sensors with the promise of further development into wearable devices. Semiconducting single-walled carbon nanotubes (SWNTs) lend themselves well to applications requiring flexibility while achieving high-performance. Our previous work has demonstrated a tri-layer polymer dielectric composed of poly(lactic acid) (PLA), poly(vinyl alcohol) with cellulose nanocrystals (PVAc), and toluene diisocyanate-terminated poly(caprolactone) (TPCL), yielding an environmentally benign and solution-processable n-type thin-film transistor (TFT).
View Article and Find Full Text PDFUnveiling the impact of biodegradable polylactic acid microplastics on meadow soil health.
Environ Geochem Health
January 2025
School of Resources and Environment, Yili Normal University, Yining, 835000, China.
Soil microplastics (MPs) pollution has garnered considerable attention in recent years. The use of biodegradable plastics for mulching has led to significant quantities of plastic entering agro-ecosystems. However, the effects of biodegradable polylactic acid (PLA) plastics on meadow soils remain underexplored.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!