Aim: To evaluate the shear strength of Orthocem and BracePaste polymerizable cement light-cured with light-emitting diode (LED) units with different wavelengths (Bluephase N) with their high power, low power, and soft start programs in the bonding of metal brackets.
Materials And Methods: experimental research was performed. Mini Roth 0.022 metal brackets (Roth Orthometric brackets) were used. The adhesives were placed on the metal brackets with Orthocem and BracePaste resin cement. To compare the average strengths, the analysis of variance (ANOVA) test was used ( < 0.05).
Results: The average shear strength was better with Bracepaste polymerizable cement compared to Orthocem cement in all its high power, low power, and soft star programs; the highest was Bracepaste with soft start of 26.52 MPa, and the lowest was Orthocem with soft start of 13.92 MPa. When evaluating the differences, it was found that these were statistically significant in all groups ( < 0.05).
Conclusions: Differences were found in the shear strength of light-curing Orthocem and Bracepaste light-curing cement cured with LED units with different wavelengths in bonding metal brackets to the tooth .
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10597364 | PMC |
| http://dx.doi.org/10.4103/jos.jos_15_23 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Influence of rock bolt reinforcement on shear behaviour of a nonpersistent joint plane.
Sci Rep
December 2024
School of Civil Engineering and Architectures, Shandong University of Science and Technology, Qingdao, 266590, People's Republic of China.
The impact of rock bolts on the mechanical behavior of nonpersistent joints, including the intricate interactions between the joints, rock bridges, and rock bolts, has received limited investigation despite their effectiveness in reinforcing rock mass discontinuities. In order to tackle this issue, a variety of normal stresses were applied during direct shear tests conducted on artificial rock-like specimens with nonpersistent joints, both bolted and unbolted. Meanwhile, to measure the deformation in the rock bridge and joint plane region, a set of strain gauges were implemented.
View Article and Find Full Text PDFHyperelastic models for the human zona pellucida and their implications on shear modulus estimation in the clinical practice.
Sci Rep
December 2024
Fertility and IVF Unit, Department of Obstetrics and Gynecology, Soroka University Medical Center, Beer Sheva, 151, Israel.
It has long been speculated that the mechanical properties of the human oocyte can be an indicator for oocyte viability. Recent studies have demonstrated that embryo implantation rates, following Intra-Cytoplasmic Sperm Injection (ICSI) procedures, may be increased if the shear modulus value of the oocyte Zona Pellucida (ZP) is taken into consideration during embryo transfer. The shear modulus was determined by an iterative oocyte specific finite element (FE) analysis based on the clinical ICSI data.
View Article and Find Full Text PDFTo investigate the influence of cations on the microstructural characteristics of electrochemical reinforcement in soft clay, a study was conducted using three different cationic salt solutions-NaCl, CaCl₂, and FeCl₃-for grouting treatment. Four sets of indoor experiments were performed to examine the reinforcement mechanism of the electrochemical method. The findings indicate that increasing the valence of injected cations significantly affects the electrochemical reinforcement effect and the soil's microstructural properties.
View Article and Find Full Text PDFShear bond strength and ARI scores of metal brackets to glazed glass ceramics and zirconia: an in vitro study investigating surface treatment protocols.
BMC Oral Health
December 2024
Faculty of Dentistry, Innovative Dental Materials and Interfaces Research Unit (URB2i), UR 4462, Paris Cité University, 1 rue Maurice Arnoux, Montrouge, 92120, France.
Objective: To evaluate the shear bond strength (SBS) and adhesive remnant index (ARI) scores of metal brackets to glazed lithium disilicate reinforced glass-ceramics and zirconia according to various surface treatment protocols.
Methods: A total of 240 lithium disilicate ceramic (LD) and 240 zirconia (Zr) blocks were randomly divided according to sandblasting, hydrofluoric acid (HF) etching, universal primer use, and the adhesive system applied. A maxillary canine metal bracket was bonded to each sample with resin cement (Transbond XT, TXT).
Assessment of surface treatment methods for strengthening the interfacial adhesion in CARALL fiber metal laminates.
Sci Rep
December 2024
Department of Mechanical and Industrial Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, 576104, Karnataka, India.
Metal and polymer interface bonding significantly influences the mechanical performance of fiber metal laminates (FMLs). Therefore, the effect of surface treatments (mechanical abrasion, nitric acid etching, P2 etching, sulfuric acid anodizing (SAA), and electric discharge machine (EDM) texturing) carried on aluminum 2024-T3 alloy sheets was evaluated considering surface morphology, surface topography, and surface roughness. Further, the influence of surface treatments on interfacial adhesion strength and failure mode between the aluminum alloy and carbon fiber prepreg was investigated.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!