Purpose: Morphological changes to the optic nerve head (ONH) can be detected at the early stages of glaucoma. Three-dimensional imaging and analysis may aid in the diagnosis. Light field (LF) fundus cameras can generate three-dimensional (3D) images of optic disc topography from a single shot and are less susceptible to motion artifacts. Here, we introduce a processing method to determine diagnostically relevant ONH parameters automatically and present the results of a subject study performed to validate this method.
Methods: The ONHs of 17 healthy subjects were examined and images were acquired with both an LF fundus camera and by optical coherence tomography (OCT). The LF data were analyzed with a novel algorithm and compared with the results of the OCT study. Depth information was reconstructed, and a model with radial basis functions was used for processing of the 3D point cloud and to provide a finite surface. The peripapillary rising and falling edges were evaluated to determine optic disc and cup contours and finally calculate the parameters.
Results: Nine of the 17 subjects exhibited prominent optic cups. The contours and ONH parameters determined by an analysis of LF 3D imaging largely agreed with the data obtained from OCT. The median disc areas, cup areas, and cup depths differed by 0.17 mm², -0.04 mm², and -0.07 mm, respectively.
Conclusions: The findings presented here suggest the possibility of using LF data to evaluate the ONH.
Translational Relevance: LF data can be used to determine geometric parameters of the ONH and thus may be suitable for future use in glaucoma diagnostics.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10382995 | PMC |
http://dx.doi.org/10.1167/tvst.12.7.21 | DOI Listing |
Sensors (Basel)
December 2024
Department of Electrical Engineering, Chinese Culture University, Taipei 11114, Taiwan.
This paper presents an effective three-dimensional (3D) surface reconstruction technique aimed at profiling composite surfaces with both specular and diffuse reflectance. Three-dimensional measurements based on fringe projection techniques perform well on diffuse reflective surfaces; however, when the measurement targets contain both specular and diffuse components, the efficiency of fringe projection decreases. To address this issue, the proposed technique integrates digital holography into the fringe projection setup, enabling the simultaneous capture of both specular and diffuse reflected light in the same optical path for full-field surface profilometry.
View Article and Find Full Text PDFSensors (Basel)
December 2024
Department of Agricultural, Alimentary, Environmental and Forestry Sciences, Biosystem Engineering Division-DAGRI, University of Florence, Piazzale delle Cascine 15, 50144 Florence, Italy.
The present research aimed to evaluate whether two sensors, optical and laser, could highlight the change in olive trees' canopy structure due to pruning. Therefore, two proximal sensors were mounted on a ground vehicle (Kubota B2420 tractor): a multispectral sensor (OptRx ACS 430 AgLeader) and a 2D LiDAR sensor (Sick TIM 561). The multispectral sensor was used to evaluate the potential effect of biomass variability before pruning on sensor response.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
Department of Polymer and Biomaterials Science, Faculty of Chemical Technology and Engineering, West Pomeranian University of Technology in Szczecin, Al. Piastów 45, 70-311 Szczecin, Poland.
Photocurable materials offer a rapid transition from a liquid to a solid state, and have recently received great interest in the medical field. However, while dental resins are very popular, only a few materials have been developed for soft tissue repair. This study aims to synthesize a difunctional methacrylate monomer using a dibutyltin dilaurate which is suitable for the photocuring of soft materials.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
School of Civil Engineering, Anhui Jianzhu University, Hefei 230601, China.
In recent years, there have been many studies focused on improving the performance of active materials; however, applying these materials to active machines still presents significant challenges. In this study, we introduce a light-powered self-translation system for an asymmetric friction slider using a liquid crystal elastomer (LCE) string oscillator. The self-translation system was composed of a hollow slide, two LCE fibers, and a mass ball.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
Graduate School of Organic Materials Science, Yamagata University, Yamagata 990-8510, Japan.
Glass short fiber-reinforced thermoplastics (GSFRTPs) are a cost-effective alternative to other short fiber-reinforced thermoplastics (SFRTPs). Their excellent mechanical properties make them a suitable material for components that require rigidity and light weight in widely diverse fields, including transportation and office automation equipment. The melt-mixing process is used to shorten glass fibers.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!