We conducted this experiment to compare the task performance of Type A and Type B persons following failure on a task in which no one succeeded (universal failure) versus failure on a task in which others had succeeded (personal failure). Postfailure performance was measured in terms of speed of completion of anagrams. Initial analyses indicated that the failure manipulation was effective in influencing the subjects' perceived cause of their failures, and that subjects were more anxious and depressed following personal failure than universal failure. More important, we found that Type A subjects performed better following personal rather than universal failure, whereas type of failure had no effect on the performance of Type B subjects. The results suggest that contrary to what is usually thought, Type A persons do not struggle for success indiscriminately. The results are discussed in terms of need for control and self-esteem.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1037//0022-3514.51.2.459 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Application of additive manufacturing TaBw01 porous tantalum rod in ARCO stage II osteonecrosis of the femoral head.
J Orthop Surg Res
December 2024
Center for Joint Surgery, Southwest Hospital, Army Medical University, Gaotanyan Street, Shapingba District, Chongqing, 400038, China.
Purpose: This study aims to investigate the suitable surgical strategies for applying TaBw01 porous tantalum rod across different stages of osteonecrosis of the femoral head (ONFH).
Methods: TaBw01 tantalum rods were fabricated using type FTaY-1 tantalum powder via the foam impregnation-sintering method. Mechanical testing with the Instron 8801 universal testing machine and finite element analysis (FEA) assessed single tantalum rod implantation and impaction bone grafting combined with rod implantation.
Influence of chlorhexidine dentin disinfection on universal adhesive performance: Interfacial adaptation and bond strength assessments.
PLoS One
December 2024
Departement of Restorative Dentistry, Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia.
Purpose: This study aimed to investigate the effect of chlorhexidine (CHX) cavity disinfectant on interfacial microleakage and micro-tensile bond strength (μTBS) of a universal adhesive bonded to dentin in both self-etch (SE) and etch-and-rinse (ER) modes.
Methods: Class I cavities were prepared in the coronal dentin of extracted human teeth and assigned to two etching modes (SE or ER), then subdivided by disinfection with or without CHX (n = 5). Cavities were restored using Single Bond Universal Adhesive and Filtek Z350 XT composite.
A tension system for angular correction of bent intramedullary nails: in vitro analysis.
Eur J Orthop Surg Traumatol
December 2024
Department of Orthopedics and Trauma, Universidade Federal Fluminense (UFF), Niterói, Rio de Janeiro, Brazil.
Purpose: Although several techniques have been described for bent intramedullary nail removal, there is no universally accepted strategy. We hypothesized that a device based on the action principle of a three-point bend fixture could facilitate extraction of bent intramedullary nails; this paper describes its design and experimental testing.
Methods: Five large synthetic left femurs and five steel intramedullary nails were used.
Implementation of a Comprehensive Protocol for Enhanced Recovery After Surgery (ERAS) in Kidney Transplant Recipients Improves Patient and Graft Outcomes.
Clin Transplant
January 2025
Glickman Urological & Kidney Institute, Cleveland Clinic, Cleveland, Ohio, USA.
Background: Enhanced recovery after surgery (ERAS) protocols have gained widespread acceptance as a means to enhance surgical outcomes. However, the intricate care required for kidney transplant recipients has not yet led to the establishment of a universally recognized and dependable ERAS protocol for kidney transplantation.
Objective: We devised a customized ERAS protocol to determine its effectiveness in improving surgical and postoperative outcomes among kidney transplant recipients.
Intelligent identification and warning method of disc cutter abnormal wear in TBM construction based on extreme learning machine.
Sci Rep
December 2024
Xinjiang Irtysh River Investment and Development (Group) Co., Ltd., Wulumuqi, 830000, China.
Abnormal cutter wear has a serious impact on TBM construction. If not found in time, it may lead to the cutterhead overall failure. Aiming at this problem, a general model and method to identify and warn the abnormal cutter wear using Extreme Learning Machine (ELM) is proposed.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!