Since the blueprints of the Liberator were published and successfully tested, countless new designs for said 3D-printed firearms and 3D-printed firearm components have been created and made publicly available. These new 3D-printed firearms, which are praised by their designers as ever more reliable, can be found on the Internet with little effort. Press reports have shown that various models of 3D-printed firearms have already been confiscated by law enforcement services around the world. So far, forensic studies have addressed this set of problems relatively little, whereby for the most part only the Liberator has been examined in detail and three other designs were only included a few times. The rapid pace of this development poses new challenges for forensic investigations and unveil new spheres of investigation regarding 3D-printed firearms. This research initiative aims to determine whether the results from previous studies on Liberators, are also reproducible and observable when using other models of 3D-printed firearms. In this respect six fully 3D-printed firearms - PM422 Songbird, PM522 Washbear, TREVOR, TESSA, Marvel Revolver and Grizzly - were produced on a material extrusion type Prusa i3 MK3S using PLA as the material. Test firings of these 3D-printed firearms have shown that they are indeed functional, but that, depending on the model, they suffer different levels of damage when fired. However, they were all rendered inoperative after one discharge and could not be used for further discharges unless the broken pieces were replaced. As in other studies, the firing process and the resulting ruptures on the 3D-printed firearm, projected polymer parts and fragments of different sizes and in different quantities into the immediate environment. The parts could be physically matched, allowing the reconstruction and identification of the 3D-printed firearms. Elements of ammunition also showed traces of melted polymer on the surface and cartridge cases bore tears or swellings.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.forsciint.2023.111736 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Technical note: A silenced hybrid 3D-printed self-loading pistol of the YEET family.
Forensic Sci Int
January 2025
Ballistics laboratory, National Institute for Criminalistics and Criminology, Vilvoordsesteenweg 98, Brussels 1120, Belgium. Electronic address:
Since the release of the first 3D-printed firearm, "The Liberator," the occurrence of 3D-printed firearms in criminal activities has increased, highlighting the need for forensic research on these weapons. This study presents a technical examination of a 3D-printed firearm received by the National Institute of Criminalistics and Criminology (NICC), focusing on its design, ballistic performance, and its potential for microscopic comparative analysis. The firearm, resembling a 3D-printed pistol Yeet22, is primarily constructed from polymer parts, with the exception of the firing pin, barrel, and various springs and screws.
View Article and Find Full Text PDFThe use of micro-CT in the investigation of a case involving 3D printed firearms.
Forensic Sci Int
October 2024
Forensic Centre for Digital Scanning and 3D Printing, WMG, University of Warwick, Coventry CV4 7AL, UK.
This paper highlights how micro-CT was used to assist in the investigation of hybrid firearms constructed using a mixture of plastic and metal components, as a complementary technique to the physical examination performed by firearms experts. In recent years, there has been an increase in the complexity and sophistication of 3D printed and hybrid firearm designs. This was also the case in the investigation presented herein, with the firearms seized demonstrating a step change in the threat level they pose through their complexity.
View Article and Find Full Text PDFReconstruction of the Talus and Calcaneus Using a Three-Dimensional (3D)-Printed Custom Implant Following a Shotgun Wound: A Case Report.
Cureus
March 2024
Department of Orthopedic Surgery, Baptist Health South Florida, Miami, USA.
We present a case detailing the successful reconstruction of the hindfoot in a 15-year-old male patient who suffered a self-inflicted shotgun wound. The patient had multiple complex fractures in these bones, resulting in considerable bone loss and the destruction of the articular surface. Considering the extent of the injuries and the failure of prior intervention from an outside surgeon, traditional reconstruction methods would not have adequately addressed the severity of the damage.
View Article and Find Full Text PDFThe emergence of 3D-printed firearms: An analysis of media and law enforcement reports.
Forensic Sci Int Synerg
March 2024
Ecole des Sciences criminelles, University of Lausanne, Switzerland.
3D-printed firearms, an emerging category of privately made firearms (PMF) produced beyond government control, have become increasingly prevalent due to technological advancements. They are now emerging as a cost-effective and reliable alternative to conventional firearms. Raised to public awareness following the 2013 release of the 3D-printed Liberator, these firearms are now more commonly encountered by police forces.
View Article and Find Full Text PDFChemical analysis of polymers used for 3D printing of firearms.
Forensic Sci Int
April 2024
Université du Québec à Trois-Rivières, Department of Chemistry, Biochemistry and Physics, 3351 Des Forges Blvd., Trois-Rivières, Québec G9A 5H7, Canada; Université du Québec à Trois-Rivières, Groupe de Recherche en Science Forensique, 3351 Des Forges Blvd., Trois-Rivières, Québec G9A 5H7, Canada; Centre International de Criminologie Comparée, PO Box 6128, Station Centre-ville, Montréal, Québec H3C 3J7, Canada.
3D-printed firearms cause challenges in criminal investigations and forensic analysis because they are difficult to trace. Indeed, in addition to being "ghost guns", they may not produce all the conventional ballistic traces normally used for firearm identification. However, 3D-printed firearms produce other very specific traces, such as polymer traces which come from the polymers used to print the firearm.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!