Thermally Stable Silicone Elastomer Composites Based on MoS@Biomass-Derived Carbon with a High Dielectric Constant and Ultralow Loss for Flexible Microwave Electronics.

ACS Appl Mater Interfaces

Institute for Composites Science Innovation (InCSI), School of Materials Science and Engineering, Zhejiang University, 38 Zheda Road, Hangzhou 310027, P. R. China.

Published: June 2023

With the miniaturization and integration of electronic components in wireless communication and wearable devices, the demand for low-cost flexible composites with temperature-stable high dielectric constant and low loss has substantially increased. However, such comprehensive properties are fundamentally difficult to combine for conventional conductive and ceramic composites. Here, we develop silicone elastomer (SE) composites based on hydrothermally grown MoS on tissue paper-derived cellulose carbon (CC). Such design promoted the formation of microcapacitors, multiple interfaces, and defects reinforcing interfacial and defect polarizations and resulting in a high dielectric constant of 9.83 at 10 GHz with low filler loading of 15 wt %. Unlike highly conductive fillers, MoS@CC with low conductivity ensured a very low loss tangent of 7.6 × 10, which was also influenced by the filler dispersion and adhesion to the matrix. Apart from breaking the typical conflict between high dielectric constant and low losses of traditional conductive composites, MoS@CC SE composites were highly flexible with temperature-stable dielectric properties making them attractive as flexible substrates in microstrip antenna applications and extreme environment electronics. Moreover, recycling from waste tissue paper makes them potential candidates as low-cost and sustainable dielectric composites.

Download full-text PDF

Source
http://dx.doi.org/10.1021/acsami.3c02587DOI Listing

Publication Analysis

Top Keywords

high dielectric
16
dielectric constant
16
silicone elastomer
8
elastomer composites
8
composites based
8
constant low
8
low loss
8
composites
7
dielectric
6
low
5

Similar Publications

A multi-band high-sensitivity microwave sensor for simultaneous detection of two dielectric materials.

Rev Sci Instrum

January 2025

The State Key Laboratory of Complex Electromagnetic Environment Effects on Electronic and Information System, Luoyang 471004, China.

A multi-band high-sensitivity microwave sensor is reported. The two resonance units are based on complementary square spiral resonators (CSSRs) and produce four measurement bands through parasitic resonances. The four frequency bands are 2.

View Article and Find Full Text PDF

Improving Image Quality and Decreasing SAR With High Dielectric Constant Pads in 3 T Fetal MRI.

J Magn Reson Imaging

January 2025

Department of Radiology, Nanjing Drum Tower Hospital, Affiliated Hospital of Medical School, Nanjing University, Nanjing, Jiangsu, China.

Background: At high magnetic fields, degraded image quality due to dielectric artifacts and elevated specific absorption rate (SAR) are two technical challenges in fetal MRI.

Purpose: To assess the potential of high dielectric constant (HDC) pad in increasing image quality and decreasing SAR for 3 T fetal MRI.

Study Type: Prospective.

View Article and Find Full Text PDF

The increasing power and integration of electronic devices have intensified serious heat accumulation, driving the demand for higher intrinsic thermal conductivity in thermal interface materials, such as polydimethylsiloxane (PDMS). Grafting mesogens onto PDMS can enhance its intrinsic thermal conductivity. However, the high stability of the PDMS chain limits the grafting density of mesogens, restricting the improvement in thermal conductivity.

View Article and Find Full Text PDF

Traditional photosensitive polyimide (PSPI) materials require a high curing temperature and exhibit low transparency, limiting their applications in thermally sensitive optical devices. To overcome this challenge, soluble photosensitive polyimide resins were synthesized based on the structural design of a bio-based magnolol monomer. It is noteworthy that the PI photoresist, developed by using the as-prepared polyimides and non-toxic solvents (2-acetoxy-1-methoxypropane, PGEMA) and other additives, demonstrated an impressive low-temperature curing performance (180 °C).

View Article and Find Full Text PDF

Integration of Through-Sapphire Substrate Machining with Superconducting Quantum Processors.

Adv Mater

January 2025

Oxford Quantum Circuits, Thames Valley Science Park, Shinfield, Reading, RG2 9LH, UK.

A sapphire machining process integrated with intermediate-scale quantum processors is demonstrated. The process allows through-substrate electrical connections, necessary for low-frequency mode-mitigation, as well as signal-routing, which are vital as quantum computers scale in qubit number, and thus dimension. High-coherence qubits are required to build fault-tolerant quantum computers and so material choices are an important consideration when developing a qubit technology platform.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!