The process of curing the acrylic oligomers for rapid thermal curing coatings in the presence of hexa(methoxymethyl)melamine (HMMM), tetra(butoxymethyl)glycoluril (TBMG), and tetra(methoxymethyl)glycoluril (TMMG) has been studied. When HMMM is used as a hardener, the content of hydroxyl groups in the terpolymer and also the crosslinking agent concentration have little effect on the initial cure rate. It has been established that during the curing of the TMMG composition, the amount of the network polymer and the initial curing rate decrease at short curing times only. It has also been revealed that the use of butoxy groups instead of methoxy groups as blocking agents leads both to a decrease in the initial cure rate and the gel fraction limiting value from 98 to 80%. When it comes to TBMG-containing compositions, a decrease in the part of hydroxyl groups in the copolymer leads to a significant fall in the initial curing rate and also in the gel fraction content. Regardless of the crosslinking agent used, an acceleration of the curing process is observed with an increase in the catalyst content in the compositions.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10180959 | PMC |
| http://dx.doi.org/10.3390/polym15092187 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Self-Healing Flexible Fiber Optic Sensors for Safe Underwater Monitoring.
ACS Appl Mater Interfaces
January 2025
State Key Laboratory of Pulp and Paper Engineering, School of Light Industry and Engineering, South China University of Technology, Guangzhou 510641, People's Republic of China.
The advancement of underwater monitoring technologies has been significantly hampered by the limitations of traditional electrical sensors, particularly in the presence of electromagnetic interference and safety concerns in aquatic environments. Fiber optic sensors are therefore nowadays widely applied to underwater monitoring devices. However, silicon- and polymer-based optical fibers often face challenges, such as rigidity, susceptibility to environmental stress, and limited operational flexibility.
View Article and Find Full Text PDFIntroduction Half of all patients with testicular germ cell tumours (GCTs) present with metastases to retroperitoneal lymph nodes or visceral organs. Inguinal metastases (I/M) are very rare. We aimed to evaluate the relative frequency and clinical features of I/M and to look for predisposing factors.
View Article and Find Full Text PDFEffect of post-processing on the surface, optical, mechanical, and dimensional properties of 3D-printed orthodontic clear retainers.
Clin Oral Investig
January 2025
School of Materials Science and Innovation, Faculty of Science, Mahidol University, Phuttamonthon 4 Road, Salaya, Phuttamonthon District, Nakhon Pathom, 73170, Thailand.
Objectives: To address the high surface roughness and poor optical properties of three-dimensional (3D) printed orthodontic clear retainers, an alternative post-processing protocol was investigated with the goal of achieving improved surface, optical, and mechanical properties while preserving dimensional accuracy.
Materials And Methods: Samples were prepared from two biocompatible methacrylate-based 3D-printing resins (Formlabs Dental LT Clear V2, NextDent OrthoFlex) and one thermoplastic material (Duran). For the 3D-printed resins, one group was post-processed by rinsing in isopropyl alcohol, while another group was centrifuged before post-curing in glycerine.
Prognostic factors for refractory outcome in localizing TIO: experience in a tertiary center.
J Clin Endocrinol Metab
January 2025
Division of Endocrinology and Metabolism, Department of Medicine, Mayo Clinic Rochester, USA.
Context: TIO, a paraneoplastic disorder characterised by renal phosphate wasting, is cured by surgical removal of the culprit tumour. Despite correct localization, some remain refractory to intervention, resulting in substantial long-term medical complications.
Aim: We aim to identify risk factors associated with a refractory outcome.
Visible-Light-Fueled Polymerizations for 3D Printing.
Acc Chem Res
January 2025
Department of Chemistry, The University of Texas at Austin, 105 East 24th Street, Austin, Texas 78712, United States.
ConspectusLight-driven polymerizations and their application in 3D printing have revolutionized manufacturing across diverse sectors, from healthcare to fine arts. Despite the popularized notion that with 3D printing "imagination is the only limit", we and others in the scientific community have identified fundamental hurdles that restrict our capabilities in this space. Herein, we describe the group's efforts in developing photochemical systems that respond to nontraditional colors of light to elicit the rapid, spatiotemporally controlled formation of plastics.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!