Inflammatory response in macrophages on account of prostheses-derived wear particles is the leading cause of artificial joint failure. However, the mechanism by which wear particles initiate macrophage inflammation has not been fully elucidated. Previous research studies have identified TANK-binding kinase 1 (TBK1) and stimulator of interferon genes (STING) as potential factors in inflammation and autoimmune diseases. Here, we found that both TBK1 and STING were increased in synovium from aseptic loosening (AL) patients and were activated in titanium particles (TiPs)-stimulated macrophages. Lentivirus-mediated knockdown of TBK or STING significantly inhibited the inflammatory effects of macrophages, while overexpression of TBK or STING exerted opposite results. In concrete, STING/TBK1 promoted the activation of NF-κB and IRF3 pathways and macrophage M1 polarization. For further validation, a mice cranial osteolysis model was constructed for in vivo assays, and we found that STING-overexpressed lentivirus injection exacerbated osteolysis and inflammation, which was counteracted by TBK1-knockdown injection. In conclusion, STING/TBK1 enhanced TiP-induced macrophage inflammation and osteolysis via orchestrating the activation of NF-κB and IRF3 pathways and M1 polarization, which suggested STING/TBK1 as potential therapeutic targets for preventing AL of prostheses.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/acsbiomaterials.2c01509 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Sterilization and Filter Performance of Nano- and Microfibrous Facemask Filters - Electrospinning and Restoration of Charges for Competitive Sustainable Alternatives.
Macromol Rapid Commun
December 2024
Empa, Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Biomimetic Membranes and Textiles, St. Gallen, 9014, Switzerland.
Facemask materials have been under constant development to optimize filtration performance, wear comfort, and general resilience to chemical and mechanical stress. While single-use polypropylene meltblown membranes are the established go-to material for high-performing mask filters, they are neither sustainable nor particularly resistant to sterilization methods. Herein an in-depth analysis is provided of the sterilization efficiency, filtration efficiency, and breathing resistance of selected aerosol filters commonly implemented in facemasks, with a particular focus on the benefits of nanofibrous filters.
View Article and Find Full Text PDFStudy on the mechanism of erosion and wear of elbow pipes by coarse particles in filling slurry.
Sci Rep
December 2024
The Ministry of Education Key Laboratory of High Efficiency Mining and Safety for Metal Mines & School of Civil and Resources Engineering, University of Science and Technology Beijing, Beijing, 100083, People's Republic of China.
Coarse particles in filling slurry are the primary factor causing wear in filling elbow pipes, and the wear mechanism of these particles on the pipes is influenced by various factors. To study the erosion and wear mechanism of elbow pipes caused by coarse particles, the motion state of coarse particles under different curvature radii, coarse particle gradations, and pipe diameters was investigated using a simulation method based on the coupling of Fluent and EDEM software, grounded in theories of fluid mechanics, rheology, and solid-liquid two-phase flow. The study explored the impact patterns and locations of wear induced by coarse particles on filling elbow pipes.
View Article and Find Full Text PDFDeveloping novel materials is an essential requirement in the engineering field. This study investigates the effects of incorporating wood dust particles on the mechanical and erosive wear properties of Luffa acutangula fiber (LAF)-reinforced phenol-formaldehyde composites, fabricated using the hand layup method with a constant 20% fiber content and varying wood dust particle contents of 0%, 10%, 20%, and 30%. Using the Taguchi method, the study identifies the optimal combination for minimizing erosive wear - 20% wood dust content, 45 m/s impact velocity, 60° impingement angle, 600 μm erodent size, and 60 mm standoff distance-achieving a minimum erosion rate of 189.
View Article and Find Full Text PDFInfluence of material-material interactions and wear on coarse waste shredders.
Waste Manag Res
December 2024
Chair of Waste Processing Technology and Waste Management, Department of Environmental and Energy Process Engineering, Montanuniversitaet Leoben, Leoben, Austria.
This article uses model materials to introduce a controlled, location- and manufacturer-independent internationally accepted method for assessing shredding machines based on large-scale tests. Furthermore, a better understanding of the comminution behaviour of shredders with fixed settings (gap width, shaft speed, cutting tool geometry) is in the focus of the present investigation and assessed, using the statistical analyses for particle size distribution in certain screen sections. Conclusions have been drawn on the comminution behaviour in general and the material-material interactions of different fractions in the grinding chamber of the shredder by showing significant differences in the pure fraction's comminution behaviour against the mixture's comminution behaviour.
View Article and Find Full Text PDFOne-Step Fabrication Process of Silica-Titania Superhydrophobic UV-Blocking Thin Coatings onto Polymeric Films.
Biomimetics (Basel)
December 2024
Department of Chemistry, Institute of Nanotechnology and Advanced Materials, Bar-Ilan University, Ramat-Gan 5290002, Israel.
Developing a durable multifunctional superhydrophobic coating on polymeric films that can be industrially scalable is a challenge in the field of surface engineering. This article presents a novel method for a scalable technology using a simple single-step fabrication of a superhydrophobic coating on polymeric films that exhibits excellent water-repelling and UV-blocking properties, along with impressive wear resistance and chemical robustness. A mixture of titanium precursors, tetraethylorthosilicate (TEOS), hydrophobic silanes and silica nano/micro-particles is polymerized directly on a corona-treated polymeric film which reacts with the surface via siloxane chemistry.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!