Background: A strong metal-cement bond is one of the many factors that contribute to the clinical success of a fixed prosthesis. Even though it is crucial to create ideal resistance and retention forms during tooth preparation, dental cement must be strong enough to hold the restoration in place in the mouth. The present study set out to evaluate and compare the binding strength of resin modified glass ionomer cement, resin cement, and glass ionomer cement to four different metal alloys: titanium alloy, cobalt-chromium (Co-Cr) alloy, nickel-chromium (Ni-Cr) alloy, and noble metal alloys (silver palladium based).
Methods: Two hundred and forty metal alloy specimens were created; these were fashioned from (i) a noble metal alloy (silver-palladium based), (ii) a titanium alloy, (iii) a cobalt-chromium alloy, and (iv) a nickel-chromium alloy. A universal testing machine was used to perform the shear test, and statistical analysis of the result was done using a two-way analysis of variance (ANOVA) test and Bonferroni test. Results:The Co-Cr alloy among the cement under investigation had the highest mean value of shear bond strength of 8.06 MPa, whereas a noble metal alloy had the lowest shear strength with a mean value of 5.36 MPa. The resin cement demonstrated the highest shear strength with a mean value that was higher than the other two types of cement. The shear bond strength of the examined samples was significantly affected by the interaction of the alloy and cement, according to the two-way ANOVA test (p=0.001).
Conclusion: The results demonstrate that resin cement offers a stronger bond, followed by resin-modified GIC and GIC. The Co-Cr alloy had the highest shear bond strength, followed by Ni-Cr, titanium, and noble metal alloy which showed significantly lower shear strength than the other three alloys.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10148197 | PMC |
| http://dx.doi.org/10.7759/cureus.36894 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effects of Different Dentin Surface Cleaning Protocols on Bond Strength of Dual-Cure Resin Cement Following Temporary Cementation.
Eur J Dent
March 2025
Department of Operative Dentistry, Faculty of Dentistry, Chulalongkorn University, Bangkok, Thailand.
Objective: The aim of this study was to compare the effectiveness of various cleaning protocols on the bond strength of dual-cure resin cement following temporary cementation.
Materials And Methods: Fifty-two human third molars were sectioned to expose superficial dentin and divided into four groups: (1) fresh, noncontaminated dentin (control); (2) pumice cleaning; (3) pumice + sodium bicarbonate air polishing; and (4) pumice + 10-methacryloyloxydecyl dihydrogen phosphate (MDP) based cleaner. Groups 2, 3, and 4 were treated with noneugenol zinc oxide temporary cement, followed by their respective cleaning protocols.
The Effect of Repair Materials and Surface Treatments on the Shear Bond Strength of 3D-Printed Provisional Restoration.
Eur J Dent
March 2025
Department of Prosthodontics, Faculty of Dentistry, Chiang Mai University, Chiang Mai, Thailand.
Objective: Despite the emergence of numerous three-dimensional (3D) printed provisional resin, there are no conclusive guidelines for repairing them. This study aims to investigate the effects of different repair materials and surface treatments on the shear bond strength of 3D-printed provisional resin.
Materials And Methods: A total of 180 3D-printed resin specimens underwent six surface treatments: no surface treatment (control), silicon carbide paper (SP), sandblasting with aluminum oxide (SB), SP followed by SB (SP + SB), SP with bonding agent (SP + BD), and SB with bonding agent (SB + BD).
Intermolecular interactions influenced the gelation and texture improvement of sturgeon surimi gels by walnut protein isolates.
Food Chem
March 2025
College of Food Science and Technology, Yunnan Agricultural University, 425 Fengyuan Road, Kunming 650201, Yunnan, China. Electronic address:
Intermolecular interaction is a key factor in the fortification of surimi gels by plant protein addition. Here, the effects of different intermolecular interactions, such as ionic, covalent and non-covalent interactions, on gel structure, gelation strength and water-holding properties were investigated, using sturgeon surimi fortified by three walnut isolates, including walnut meal (WM), protein isolate (WPI) and peptide (WP), as representatives. Quantitative creep-recovery analysis and soluble protein assay demonstrated that secondary bonds, mainly hydrophobic interaction and hydrogen bond, possibly played a dominant role in walnut protein-fortified surimi gels.
View Article and Find Full Text PDFAnalysis of the mechanical properties of bond strength in adhesive systems bonded to HCR silicone facial.
Int J Artif Organs
March 2025
Department of Dental Materials and Prosthodontics, Araçatuba Dental School, São Paulo State University (UNESP), Araçatuba, São Paulo, Brazil.
Objective: Therefore, this study aimed to evaluate the maximum displacement resistance of silicone samples adhered to human skin using different adhesives. For this purpose, colorless silicone samples (A-4530-HCRA Silicone Gum HCR) pigmented with Functional Intrinsic II Silicone Coloring System were made and distributed into five groups (1. SA specific adhesive for maxillofacial prostheses: Drying Adhesive; 2.
View Article and Find Full Text PDFEffect of various solvents on the repairability of aged CAD/CAM provisional restorative materials with flowable resin composite: an in vitro study.
BMC Oral Health
March 2025
Division of Prosthodontics, Faculty of Dentistry, Thammasat University, Pathumthani, 12120, Thailand.
Background: Increased bond strength between aged CAD/CAM (Computer-Aided Design and Computer-Aided Manufacturing) provisional restorative materials is essential for reparability. This study investigated the impact of three different solvents and airborne-particle abrasion on the shear bond strength (SBS) of aged CAD/CAM provisional restorative materials, which are milled PMMA and 3D-printed resin with flowable resin composite.
Methods: 3D-printed resin and milled PMMA (N = 160 per type) were fabricated into cylindrical shapes (5 mm in diameter, 5 mm in height), aged by 5,000 thermocycling cycles, and randomize divided at random into five groups (N = 32) based on surface modification protocols: control; non-surface modification, MEK; application with methyl ethyl ketone, THF; application with tetrahydrofuran, Alc; application with isopropyl alcohol, and APA; airborne-particle abrasion with 50-µm alumina oxide particle.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!