Oats are highly susceptible to infection by Fusarium species, especially F. langsethiae, F. poae and F. sporotrichioides which contaminate the grain with mycotoxins. Climate change is expected to affect fungal colonisation and associated mycotoxin production. The objective of this study was to examine the effect of acclimatisation to elevated CO on the growth and mycotoxin production capacity of these fungal species. Strains of F. langsethiae (FL; seven strains), F. poae (FP; two strains) and F. sporotrichioides (FS; one strain) were acclimatised by sub-culturing for 10 generations at either 400 or 1000 ppm CO under diurnal temperature conditions. At each sub-culturing, the effect of acclimatisation to elevated CO on (a) lag phase prior to growth, (b) growth rate on oat-based media was assessed. Additionally, the production of type A trichothecenes and related toxic secondary metabolites of sub-cultures after 1, 7 and 10 generations were assessed using LC-MS/MS qTRAP. The results showed that Fusarium strains had an increased lag time and growth rate in response to the combined effect of sub-culturing and elevated CO levels. T-2 + HT-2 production was affected by elevated CO in strain FL4 (7.1-fold increase) and a decrease in strain FL1 (2.0-fold decrease) at the first sub-culturing and FS (1.3-fold decrease) after 7 sub-cultures compared to ambient conditions. The effect of sub-culturing on T-2 + HT-2 production varied depending on the fungal strain. For strain FL4, significantly less T-2 + HT-2 toxins were produced after 10 generations (4.4-fold decrease) as compared to that under elevated CO conditions after one sub-culture, and no change was observed under ambient conditions. The FS strain showed significant stimulation of T-2 + HT-2 toxin production after 10 sub-cultured generations (1.1-fold increase) compared to the initial sub-culture of this strain under elevated CO conditions. The production of other toxic secondary metabolites was generally not impacted by elevated CO conditions or by sub-culture for 10 generations, with the exceptions of FL1 and FP1. FL1 produced significantly more neosolaniol after 10 generations, when compared to those after 1 and 7, regardless of the CO conditions. For FP1, elevated CO significantly triggered beauvericin production after an initial sub-culture when compared to ambient conditions at the same sub-culture stage (29-fold). FP1 acclimatisation to elevated CO led to a decrease of beauvericin production after 10 generations when compared to 1 (6-fold). In contrast, sub-culturing for 10 generations compared to 1 under ambient CO conditions resulted in an increase in this toxin (12-fold).
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.ijfoodmicro.2023.110176 | DOI Listing |
Proc Natl Acad Sci U S A
January 2025
Department of Mechanical and Aerospace Engineering, Carleton University, Ottawa, ON K1S 5B6, Canada.
Limiting climate change to targets enshrined in the Paris Agreement will require both deep decarbonization of the energy system and the deployment of carbon dioxide removal at potentially large scale (gigatons of annual removal). Nations are pursuing direct air capture to compensate for inertia in the expansion of low-carbon energy systems, decarbonize hard-to-abate sectors, and address legacy emissions. Global assessments of this technology have failed to integrate factors that affect net capture and removal cost, including ambient conditions like temperature and humidity, as well as emission factors of electricity and natural gas systems.
View Article and Find Full Text PDFLangmuir
January 2025
Department of Chemical and Pharmaceutical Engineering, Faculty of Chemistry and Pharmacy, Sofia University, 1 James Bourchier Avenue, Sofia 1164, Bulgaria.
Spontaneous bubble growths in liquids are usually triggered by rapid changes in pressure or temperature that can lead to liquid gas supersaturation. Here, we report alternative scenarios of the spontaneous growths of bubbles inside a high-saturation-vapor-pressure and high-air-solubility perfluorocarbon liquid (PP1) that were observed under ambient quiescent conditions. First, we investigate spontaneous bubble growth inside the single PP1 phase, which was left to evaporate freely.
View Article and Find Full Text PDFJ Am Chem Soc
January 2025
Department of Materials Science, Fudan University, Shanghai 200433, China.
Borohydrides, known for ultrahigh hydrogen density, are promising hydrogen storage materials but typically require high operating temperatures due to their strong thermodynamic stability. Here we introduce a novel light-induced destabilization mechanism for hydrogen storage reaction of borohydrides under ambient conditions photogenerated vacancies in LiH. These vacancies thermodynamically destabilize B-H bonds through the spontaneous "strong adsorption" of BH groups, which trigger an asymmetric redistribution of electrons, enabling hydrogen release at near room temperature, approximately 300 °C lower than the corresponding thermal process.
View Article and Find Full Text PDFEur Psychiatry
January 2025
Department of Psychiatry and Neuropsychology, School for Mental Health and Neuroscience, Maastricht University Medical Center, Maastricht, The Netherlands.
Background: Temperature increases in the context of climate change affect numerous mental health outcomes. One such relevant outcome is involuntary admissions as these often relate to severe (life)threatening psychiatric conditions. Due to a shortage of studies into this topic, relationships between mean ambient temperature and involuntary admissions have remained largely elusive.
View Article and Find Full Text PDFACS Mater Lett
January 2025
Air Force Research Laboratory, Materials and Manufacturing Directorate, Wright-Patterson AFB, Ohio 45433, United States.
Photocurable self-healing elastomers are promising candidates for producing complex soft devices that can mend damage. However, the practicality of these materials is limited by reliance on external stimuli, custom synthesis, manual realignment, and multihour healing cycles. This paper introduces a tough 3D-printable hybrid acrylate/thiol-ene elastomer (prepared with commercially available precursors) that exhibits nearly instantaneous damage repair in the absence of external stimuli.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!