The latex used conventionally for oil-well cementing can lead to serious foaming issues in the cement slurry, which not only affects the accurate measurement of the density of the latex-containing cement slurry, but also is detrimental to cementing construction. A large amount of a foam stabilizer used for latex preparation is mainly responsible for foaming of the latex-containing cement slurry. In this study, soap-free emulsion polymerization was conducted using 2-acrylamido-2-methylpropanesulfonic acid (AMPS), styrene (St), and butyl acrylate (BA) as the reaction monomers and the effects of the AMPS dosage, monomer ratio, reaction temperature and stirring speed on the performance of the latex were investigated. The optimum synthesis conditions included a 30% monomer concentration, an St : BA : AMPS monomer ratio of 5 : 4 : 6, a synthesis temperature of 85°C, a stirring speed of 400 r.p.m. and 1.5% of the initiator. As-prepared latex exhibited good filtration loss control, excellent freeze-thaw stability, and extremely low foaming of the cement slurry with the added latex, which was extremely beneficial for on-site cementing construction.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9943870 | PMC |
| http://dx.doi.org/10.1098/rsos.221319 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Woven Cement Slurry.
Adv Mater
January 2025
College of Civil Engineering and Architecture, Zhejiang University, Hangzhou, 310058, China.
Weaving, a pivotal technique in human construction activities since the Neolithic era, remains unattainable in modern concrete construction. Here, a novel particle-polymer coalescence strategy is proposed, which involves electrostatic, bridging, coordinating, and hydrogen bonding interactions, to establish balanced particle cohesion, enabling the fabrication of stretchable cement slurry. The bending, knotting, coiling, winding, and interlacing of cement filaments for structural textiles is successfully realized beyond traditional formwork casting, grouting, and 3D-printing, and fabricate the first-ever Chinese knot woven with cement.
View Article and Find Full Text PDFFlexural Response Comparison of Nylon-Based 3D-Printed Glass Fiber Composites and Epoxy-Based Conventional Glass Fiber Composites in Cementitious and Polymer Concretes.
Polymers (Basel)
January 2025
School of Civil Engineering and Environmental Science, University of Oklahoma, 202 W Boyd St., Norman, OK 73019, USA.
With 3D printing technology, fiber-reinforced polymer composites can be printed with radical shapes and properties, resulting in varied mechanical performances. Their high strength, light weight, and corrosion resistance are already advantages that make them viable for physical civil infrastructure. It is important to understand these composites' behavior when used in concrete, as their association can impact debonding failures and overall structural performance.
View Article and Find Full Text PDFStability and Rheological Properties of Grouts with Waste Glass Powder as Cement Replacement: Influences of Content and Alkali Activator.
Materials (Basel)
January 2025
College of Civil Engineering, Changsha University of Science and Technology, Changsha 410114, China.
Effective recycling and utilization of waste glass is a critical issue that urgently needs to be addressed. This study aims to explore the feasibility of using ground waste glass powder (particle size ≤ 75 μm) as a supplementary cementitious material to partially replace cement in the preparation of low-carbon and environmentally friendly grouting materials. The research systematically evaluates the impact of waste glass powder (WGP) on the fresh properties (particularly the stability and rheological characteristics) of cement-based grouting materials under various conditions, including WGP content (0-40%), the addition of NaOH activator (NaO content of 4%) or not, and water-solid ratio (/ 0.
View Article and Find Full Text PDFEarly Strength Enhancement Mechanism of CaO-Modified Electrolytic Manganese Residue-Based Supersulfate Cement.
Materials (Basel)
January 2025
Guizhou Provincial Architectural Design & Research Institute Co., Ltd., Guiyang 550025, China.
Electrolytic manganese residue (EMR) is a solid waste generated during the production of electrolytic manganese metal through wet metallurgy, accumulating in large quantities and causing significant environment pollution. Due to its high sulfate content, EMR can be utilized to prepare supersulfate cement when combined with Ground Granulated Blast furnace Slag (GGBS). In this process, GGBS serves as the primary raw material, EMR acts as the sulfate activator, and CaO powder, along with trace amounts of cement, functions as the alkali activator.
View Article and Find Full Text PDFRecycling of Agricultural Film Wastes for Use as a Binder in Building Composites.
Materials (Basel)
January 2025
Research Team of Quantitative Methods and Spatial Management, Institute of Agriculture and Horticulture, Faculty of Agricultural Sciences, University of Siedlce, B. Prusa 14, 08-110 Siedlce, Poland.
Plastic film, also known as low-density polyethylene (LDPE), poses serious environmental challenges due to mass production, short life cycle, and poor waste management. The main aim of this paper was to examine the suitability of using agricultural waste film as a binder in construction composites instead of the traditional cement slurry. Molten at temperatures of around 120-150 °C wastes was mixed with fine sand and gravel aggregate as filler.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!