: Following the most recent software and 3D printing developments, the use of personalized 3D printed orthopedic implants for treatment of complicated surgical cases has gained more popularity. Today, orthopedic problems that cannot be solved with standard implants may be effectively addressed using personalized prostheses. The aim of this study is to present the designing, modeling and production stages of four different personalized 3D printed prostheses and their application in clinical cases of patients who underwent treatment in various anatomical locations with a precisely specified indication for implantation. : Based on computed tomography scanning, personalized 3D printed prostheses were designed, produced and used in four patients within a period of three to five days after injury or admission. : Early term follow-ups demonstrated good to excellent results. : Personalized 3D printed prostheses offer an opportunity for a treatment of choice and provide good anatomical and functional results, shortened surgical time, less complications, and high satisfaction in patients with appropriate indications. The method should be considered primarily for patients with large bone defects, or such indicated for resection. Personalized 3D printed prostheses have the potential to become more common and beneficial in the future.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9959288 | PMC |
| http://dx.doi.org/10.3390/medicina59020249 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
In vitro analysis of composition profiles of resins for 3D printing of dentures.
J Dent
January 2025
Clinic of General-, Special Care- and Geriatric Dentistry, Center for Dental Medicine, University of Zurich, Zurich, Switzerland. Electronic address:
Objective: This study aimed to investigate the resin compounds from CAD-CAM 3D-printed denture resins, focusing on the identification and classification of free monomers and other components. The primary objective was to determine the chemical profile of these 3D-prinding resin materials.
Methods: Four 3D-printed denture resins, two base materials (1: DentaBASE, Asiga Ltd.
3D printing hydrogel with homogeneous structural color induced by ZnS colloidal spheres for customized multi-channel spatial information encryption.
J Colloid Interface Sci
January 2025
State Key Laboratory of Fine Chemicals, Dalian University of Technology, 2# Linggong Road, Dalian 116024, China. Electronic address:
The utilization of structural colors in 3D printing was anticipated due to their eco-friendliness and sustainability. However, the manufacturing of homogeneous structural colors with intricate 3D architectures remains a great challenge, particularly in hydrogels. Herein, we added 0.
View Article and Find Full Text PDFMcGrath MAC Versus Three-Dimensional Printed Video Laryngoscopes: A Randomized, Manikin-Simulated Noninferiority Controlled Study with Medical Students.
Anesth Analg
February 2025
From the Department of Surgical Specialties and Anesthesiology of São Paulo State University (UNESP), Medical School, Botucatu, Brazil.
Background: Proficiency in endotracheal intubation (ETI) is essential for medical professionals and its training should start at medical schools; however, large caseload may be required before achieving an acceptable success rate with direct laryngoscopy. Video laryngoscopy has proven to be an easier alternative for intubation with a faster learning curve, but its availability in medical training may be an issue due to its high market prices. We devised a low-cost 3-dimensionally printed video laryngoscope (3DVL) and performed a randomized trial to evaluate if the intubation success rate on the first attempt with this device is noninferior to a standard commercially available video laryngoscope (STVL).
View Article and Find Full Text PDFEvaluating the impact of a hand-crafted 3D-Printed head Model and virtual reality in skull base surgery training.
Brain Spine
December 2024
Department of Neurosurgery, University Hospital of Lausanne and University of Lausanne, 1011, Lausanne, Switzerland.
Introduction: While cadaveric dissections remain the cornerstone of education in skull base surgery, they are associated with high costs, difficulty acquiring specimens, and a lack of pathology in anatomical samples. This study evaluated the impact of a hand-crafted three-dimensional (3D)-printed head model and virtual reality (VR) in enhancing skull base surgery training.
Research Question: How effective are 3D-printed models and VR in enhancing training in skull base surgery?
Materials And Methods: A two-day skull base training course was conducted with 12 neurosurgical trainees and 11 faculty members.
3D Bioprinted Head and Neck Squamous Cell Carcinoma (HNSCC) Model Using Tunicate Derived Nanocellulose (NC) Bioink.
Adv Healthc Mater
January 2025
Institute of Transfusion Medicine and Immunology, Medical Faculty Mannheim, Heidelberg University, German Red Cross Blood Donor Service Baden-Württemberg - Hessen, 68167, Mannheim, Germany.
Head and neck squamous cell carcinoma (HNSCC) are invasive solid tumors accounting for high mortality. To improve the clinical outcome, a better understanding of the tumor and its microenvironment (TME) is crucial. Three -dimensional (3D) bioprinting is emerging as a powerful tool for recreating the TME in vitro.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!