Agroecological Management of the Grey Mould Fungus by Plant Growth-Promoting Bacteria.

Plants (Basel)

Instituto de Investigaciones Químico-Biológicas, Universidad Michoacana de San Nicolás de Hidalgo, Morelia 58030, Mich, Mexico.

Published: February 2023

is the causal agent of grey mould and one of the most important plant pathogens in the world because of the damage it causes to fruits and vegetables. Although the application of botrycides is one of the most common plant protection strategies used in the world, the application of plant-beneficial bacteria might replace botrycides facilitating agroecological production practices. Based on this, we reviewed the different stages of infection in plants and the biocontrol mechanisms exerted by plant-beneficial bacteria, including the well-known plant growth-promoting bacteria (PGPB). Some PGPB mechanisms to control grey mould disease include antibiosis, space occupation, nutrient uptake, ethylene modulation, and the induction of plant defence mechanisms. In addition, recent studies on the action of anti- compounds produced by PGPB and how they damage the conidial and mycelial structures of the pathogen are reviewed. Likewise, the advantages of individual inoculations of PGPB versus those that require the joint action of antagonist agents (microbial consortia) are discussed. Finally, it should be emphasised that PGPB are an excellent option to prevent grey mould in different crops and their use should be expanded for environmentally friendly agricultural practices.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9919678PMC
http://dx.doi.org/10.3390/plants12030637DOI Listing

Publication Analysis

Top Keywords

grey mould
16
plant growth-promoting
8
growth-promoting bacteria
8
plant-beneficial bacteria
8
plant
5
pgpb
5
agroecological management
4
grey
4
management grey
4
mould
4

Similar Publications

Roses () are among the most cherished ornamental plants globally, yet they are highly susceptible to infections by , the causative agent of gray mold disease. Here we inoculated the resistant rose variety 'Yellow Leisure Liness' with to investigate its resistance mechanisms against gray mold disease. Through transcriptome sequencing, we identified 578 differentially expressed genes (DEGs) that were significantly upregulated at 24, 48, and 72 hours post-inoculation, with these genes significantly enriched for three defense response-related GO terms.

View Article and Find Full Text PDF

Remotely-sensed risk assessments of emerging, invasive pathogens are key to targeted surveillance and outbreak responses. The recent emergence and spread of the fungal pathogen, Batrachochytrium salamandrivorans (Bsal), in Europe has negatively impacted multiple salamander species. Scholars and practitioners are increasingly concerned about the potential consequences of this lethal pathogen in the Americas, where salamander biodiversity is higher than anywhere else in the world.

View Article and Find Full Text PDF

Aspergillus nidulans cell wall integrity kinase, MpkA, impacts cellular phenotypes that alter mycelial-material mechanical properties.

Fungal Biol Biotechnol

December 2024

Department of Chemical, Biochemical and Environmental Engineering, University of Maryland, Baltimore County (UMBC), 1000 Hilltop Circle, Baltimore, MD, 21250, USA.

Mycelial materials are an emerging, natural material made from filamentous fungi that have the potential to replace unsustainable materials used in numerous commercial applications (e.g., packaging, textiles, construction).

View Article and Find Full Text PDF

may cause gray mold in fruits and vegetables. Paeonol, an active component of traditional Chinese medicine, could suppress various microbial growth. However, reports on its effect on have not yet been documented.

View Article and Find Full Text PDF

The research conducted in this study aimed to determine whether the production of a layered casting in the material system of X46Cr13 steel (working part) and gray cast iron (base part) can be integrated with the hardening process of this steel within the conditions of the casting mold. Accordingly, a series of layered castings was produced by preparing the mold cavity, where a monolithic steel insert was poured with molten gray cast iron with flake graphite. The variable factors in the casting production process included the pouring temperature T and the thickness of the support part g.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!