Objective: This study aimed to evaluate the influence of new resin-based CAD-CAM implant-supported materials on posterior crown restoration stress and strain concentrations.
Methods: A previous 3D implant model was edited to receive a cement-retained posterior crown manufactured with different CAD/CAM materials (Estelite P Block, Estelite Block II or Estelite Layered Block). Each solid model was exported to the computer-aided engineering software and submitted to the finite element analysis of stress and strain. Material properties were assigned to each solid with isotropic and homogeneous behavior according to the manufacturer information. A vertical load of 600 N was applied in the occlusal region of the crown, via a simulated food bolus, and stress was calculated in Von Misses (σVM) for the implant, abutment and screw, Maximum (σMAX) Principal Stresses for the crown and microstrain for the bone.
Results: All simulated materials showed acceptable stresses levels with a similar stress pattern among the models. At the crown intaglio region and cement layer, however, differences were observed: Estelite P Block showed a lower tensile and shear stresses magnitude when compared to other resin-based materials with lower elastic modulus.
Significance: The stress effect of different resin-based CAD-CAM implant-supported crowns is predominant in the crown and cement layer, with Estelite P Block showing 7.4 % versus 9.3 % and 9.2 % for Estelite Block II and Estelite Layered Block of crown failure risk.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.dental.2022.12.001 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Stress distribution in resin-based CAD-CAM implant-supported crowns.
Dent Mater
January 2023
School of Medical Sciences and Photon Science Institute, University of Manchester, Manchester, UK.
Objective: This study aimed to evaluate the influence of new resin-based CAD-CAM implant-supported materials on posterior crown restoration stress and strain concentrations.
Methods: A previous 3D implant model was edited to receive a cement-retained posterior crown manufactured with different CAD/CAM materials (Estelite P Block, Estelite Block II or Estelite Layered Block). Each solid model was exported to the computer-aided engineering software and submitted to the finite element analysis of stress and strain.
In Silico Finite Element Analysis of Implant-Supported CAD-CAM Resin Composite Crowns.
J Prosthodont
March 2023
Department of Prosthodontics, Ankara University Faculty of Dentistry, Ankara, Turkey.
Purpose: The aim of this study was to evaluate the mechanical behavior of an implant-supported crown made using computer-aided design and computer-aided manufacturing (CAD-CAM) resin composite (RC) blocks in the posterior region.
Material And Methods: Four commercially available CAD-CAM RC blocks were used in this study: Cerasmart 300 (CS300; GC, Tokyo, Japan), Katana Avencia P Block (KAP; Kuraray Noritake Dental, Niigata, Japan); KZR HR3 Gamma Theta (HR3; Yamakin, Osaka, Japan), and Estelite P block (ESP; Tokuyama Dental, Tokyo, Japan). Katana Zirconia STML (ST; Kuraray Noritake Dental) was used as the control group.
Effects of two methyl methacrylate-tributylborane-based luting agents with a silane-phosphate primer on bonding of four different CAD/CAM resin composite materials.
J Oral Sci
April 2022
Division of Cariology and Restorative Dentistry, Department of Prosthetic Dentistry, Graduate School of Biomedical Sciences, Nagasaki University.
Purpose: This study compared the bond strengths of four adhesive systems and four different resin composite block materials: Gradia Block (GR), Shofu Block HC (SH), Estelite Block (ES), and KZR-CAD HR2 (KZ).
Methods: A primer (PZ-AB) containing a silane (γ-MPTS) with 10-methacryloyloxydecyl dihydrogen phosphate (MDP) was applied to ground surfaces of the resin composite block specimens, and the specimens were then bonded to stainless-steel rods using two methyl methacrylate-tributylborane (MMA-TBB)-based luting agents (SB and MT), designated as the PZ-AB/SB and PZ-AB/MT adhesive systems, respectively. The SB resin contained 4-methacryloyloxyethyl trimellitate anhydride (4-META), whereas the MT resin did not.
Anti-Demineralization Effects of Dental Adhesive-Composites on Enamel-Root Dentin Junction.
Polymers (Basel)
September 2021
Department of Cariology and Operative Dentistry, Division of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo 113-8549, Japan.
Oral biofilm reactor (OBR) and pH cycling (pHC) artificial caries model were employed to evaluate the anti-demineralization effects of four composite filling systems on enamel-root dentin junction. Sixty-four enamel-root dentin blocks (6 mm × 6 mm × 2 mm) each with a cylindrical cavity were randomly assigned to the pHC and OBR group, then four subgroups (n = 8) and filled with either the Beautifil II (BEF, SPRG-filler-containing) or Estelite (EST) composite after the adhesive (either Single Bond Universal (SBU) or FL Bond II (FL, SPRG-filler-containing)). The demineralization lesions of filling interface were examined by micro-computerized tomography (μCT) and swept-source-optical coherence tomography (SS-OCT).
View Article and Find Full Text PDFGloss and surface roughness of pre-polymerized composite materials designed for posterior CAD/CAM crown restorations corroded with acidulated phosphate fluoride application.
Dent Mater J
February 2022
Department of Fixed Prosthodontics, Nihon University School of Dentistry.
This study assessed the gloss and surface roughness of computer-aided design/computer-aided manufacturing (CAD/CAM) resin composites corroded with acidulated phosphate fluoride (APF) application. One ceramic block, ten CAD/CAM resin composites for premolars, and four CAD/CAM resin composites for molars were assessed. The surface topography of the materials before and after APF application was observed using an electron microscope.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!