Perfectly coated surfaces are an essential quality feature in the automotive and consumer goods industries. They are the result of an optimized, controlled coating process. Because entire assemblies could be rejected if Out-of-Specification (OOS) parts are installed, this has a severe economic impact. This paper presents a novel, line-integrated multi-camera system with intelligent algorithms for anomaly detection on small KTL-coated aluminum parts. The system also aims to automatize the previously used human inspection to a sophisticated and automated vision system that efficiently detects defects and anomalies on coated parts.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9787559 | PMC |
| http://dx.doi.org/10.3390/s22249646 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Evaluatıon of stress dıstrıbutıon by applıed dıfferent forces on ımmature maxıllary central teeth wıth dıfferent treatment optıons: a laboratory fınıte element stress analysıs.
BMC Oral Health
January 2025
Department of Endodontics, Faculty of Dentistry, Ordu University, Ordu, 52200, Turkey.
Background: Immature maxillary central teeth can be managed by using several treatment options. The aim of this finite element stress analysis study was to evaluate the effect of different treatment procedures on the stresses on immature maxillary incisor teeth models that generated on cone beam computed tomography, by trauma and bite forces.
Methods: A total of 11 different models consisting of revascularization treatment using MTA and biodentine and the state of the root apex formed with cement after treatment, apexification, modified apexification, traditional root canal treatment and two different control groups have been created.
Survival after aluminum phosphide poisoning with cardiotoxicity: a case report.
J Med Case Rep
December 2024
Department of Internal Medicine, Woldia Comprehensive Specialized Hospital, Woldia, Ethiopia.
Introduction: Aluminum phosphide is a cheap and commonly used rodenticide that is also an effective solid fumigant and frequently used for grain preservation. The pill contains around 44% inert elements (ammonium carbonate) to avoid disintegration of the tablet, while the rest (about 56%) is aluminum phosphide. Because it is freely available on the market, it is one of the commonly used agents for self-poisoning in different parts of the developing world.
View Article and Find Full Text PDFApplication of a 3D-Printed Part with Conformal Cooling in High-Pressure Die Casting Mould and Evaluation of Stress State During Exploitation.
Materials (Basel)
December 2024
Łukasiewicz Research Network-Krakow Institute of Technology, 30-418 Krakow, Poland.
The article addresses stress formation in the structural 3D-printed elements of a high-pressure die casting die mould used for production of aluminum castings. The 3D-printed elements with conformal cooling are manufactured of 18Ni300 powder. Initial numerical calculations were performed on a test die mould made of standard steel X40CrMoV5 to determine temperature distribution and stress state, providing a baseline for comparing 3D-printed 18Ni300 parts.
View Article and Find Full Text PDFPrediction of the Stability of the Casting Process by the HPDC Method on the Basis of Knowledge Obtained by Data Mining Techniques.
Materials (Basel)
December 2024
Faculty of Materials, Technical University of Kosice, Metallurgy and Recycling, Letna 1/9, 042 00 Kosice, Slovakia.
High-pressure die casting (HPDC) of aluminum alloys is one of the most efficient manufacturing methods, offering high repeatability and the ability to produce highly complex castings. The cast parts are characterized by good surface quality, high dimensional accuracy, and high tensile strength. Continuous technological advancements are driving the increase in part complexity and quality requirements.
View Article and Find Full Text PDF5-Axis CNC micro-milling machine for three-dimensional microfluidics.
Lab Chip
December 2024
Department of Biomedical Engineering, University of Connecticut, 260 Glenbrook Rd, Storrs, CT 06269 USA.
The gold standard of microfluidic fabrication techniques, SU-8 patterning, requires photolithography equipment and facilities and is not suitable for 3D microfluidics. A 3D printer is more convenient and may achieve high resolutions comparable to conventional photolithography, but only with select materials. Alternatively, 5-axis computer numerical control (CNC) micro-milling machines can efficiently prototype structures with high resolutions, high aspect ratios, and non-planar geometries from a variety of materials.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!