Comparison of the Mineral Profile of Two Types of Horse Diet, Silage and Commercial Concentrate, and Their Impacts on Hoof Tensile Strength.

Animals (Basel)

Departamento de Patología, Facultad de Medicina Veterinaria y Zootecnia, Universidad Nacional Autónoma de México, Av Universidad 3000, Mexico City 04510, Mexico.

Published: November 2022

The type of diet that a horse consumes is one of the most important factors determining the mineral profile and tensile strength of its hooves, so the quality and nutritional value of the supplied feed are fundamental to achieving satisfactory hoof quality. The objective of this study was to compare the differences in the mineral concentrations of sodium (Na), potassium (K), magnesium (Mg), zinc (Zn), and Iron (Fe) between two diets, namely silage and a commercial concentrate, using atomic absorption spectrometry and to determine which led to higher increases in the hoof tensile strength of horses consuming these diets. Thirty-two Spanish horses were randomly divided into two groups, where the diet of the horses in group 1 was silage oat hay, and that of the horses in group 2 was a commercial concentrate and oat hay. Both diets were provided for 12 months. The hoof tensile strength was then measured using an Instron universal testing machine. Mg and Fe levels were higher (p < 0.05) in the silage than in the commercial concentrate, and hoof Mg, Zn, K, and tensile strength were also influenced by the hormonal stage (p < 0.05). The type of diet directly affected the hoof Mg, Zn, K, Na, and tensile strength (p < 0.05), which Mg, K and Na were higher in horses fed with concentrate. It was found that for each unit of Zn (μg/g and Na (μg/g)), in the hoof, the tensile strength is affected by −0.10 N/mm2 and −0.003 N/mm2, respectively for each mineral.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9686781PMC
http://dx.doi.org/10.3390/ani12223204DOI Listing

Publication Analysis

Top Keywords

tensile strength
28
hoof tensile
24
commercial concentrate
16
silage commercial
12
mineral profile
8
type diet
8
horses group
8
oat hay
8
hoof
7
tensile
7

Similar Publications

This study describes procedures for embedding digital information into additively manufactured components as well as procedures for readout and tensile testing. Embedded digital codes were printed inside ASTM E8/E8M dumbbells using Direct Metal Laser Melting (DMLS) with an EOS M290 printer. The codes were configured as either ellipsoids or prolate spheroids in patterns given by the Cantor dust fractal.

View Article and Find Full Text PDF

Highly printable, strong, and ductile ordered intermetallic alloy.

Nat Commun

January 2025

Department of Materials Science and Engineering, College of Engineering, City University of Hong Kong, Hong Kong, China.

Ordered intermetallic alloys are renowned for their impressive mechanical, chemical, and physical properties, making them appealing for various fields. However, practical applications of them have long been severely hindered due to their severe brittleness and poor fabricability. It is difficult to fabricate such materials into components with complex geometries through traditional subtractive manufacturing methods.

View Article and Find Full Text PDF

Enhancement of mechanical properties in reactive polyurethane film via in-situ assembly of embedded cellulose nanocrystals.

Int J Biol Macromol

January 2025

Zhejiang Provincial Engineering Research Center for Green and Low-carbon Dyeing & Finishing, Zhejiang Sci-Tech University, Hangzhou 310018, China; Zhejiang Provincial Innovation Center of Advanced Textile Technology, Shaoxing 312000, China. Electronic address:

Comparing to the solvent-based and waterborne polyurethanes (PU), the solvent-free reactive PU (RPU) is prepared via in-situ polymerization and film-formation of isocyanate-capped prepolymers and macromolecular polyols in solvent-free system. Thus, the carbon emissions and environmental pollutions are significantly reduced. However, the rapid polymerization also challenges the well control of structure and properties, especially the ordered microstructures.

View Article and Find Full Text PDF

The study aimed to compare the effects of different types of excimer laser keratectomy on rabbit corneas and to identify the optimal disease model for corneal ectasia. Additionally, investigating the structural and molecular alterations in the novel disease model helped explore the mechanisms underlying biomechanical cues in corneal ectasia. 2.

View Article and Find Full Text PDF

This study aimed to construct oleofilms containing a binary mixture of proteins (soy protein hydrolysate and gelatin) and lipids (olive oil, stearic acid, and lecithin) using various ultrasonic emulsification processes. Initially, oleogels (OG20, OG40, OG60, OG80, and OG100) were fabricated with different sonication powers (20 %-100 %), along with control (OG) without sonication. Macrostructure, FTIR, DSC, stability coefficient (57.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!