The article describes the results of pull-off adhesion strength of the FRCM-PBO (Fiber Reinforced Cementitious Matrix-p-Phenylene benzobis oxazole) composite adhered to the epoxy resin layer which is the connector with the timber beam. In addition, this paper shows the results of the tests of resistance to pull-off the epoxy resin layer from the pine beam. The tests were carried out based on the Polish Standard PN-EN 1542. The Pearson linear correlation analysis was also carried out in order to determine the correlation between the obtained results and the destructive forces. The factors that occurred during the test that may affect its results, such as the method of applying the bursting force, surface preparation of the tested elements and the types of substrate destruction, were also characterized. The experimental data show that in all the tested samples, non-initial adhesive destruction between the adhesive layer and the disc was observed.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9657761 | PMC |
| http://dx.doi.org/10.3390/ma15217702 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
The influence of pectins and cellulose in the mechanical and adhesive properties of seed mucilage.
J Exp Bot
January 2025
Department of Functional Morphology and Biomechanics, Zoological Institute, Kiel University, Am Botanischen Garten 1-9, 24118 Kiel, Germany.
Several plant seeds release a mucilaginous envelope through hydration, rich in pectins and stabilized by cellulose fibers. This mucilage aids in seed protection, development, and adhesion for dispersal. This study aimed to separate the effects of pectins and cellulose fibers by using pectinase to remove mucilage pectins, leaving cellulose arrays, and performing wet and dry pull-off force measurements on seeds of three plant species: Salvia hispanica (Chia), Collomia grandiflora (Collomia) and Linum usitatissimum (Flax).
View Article and Find Full Text PDFInvestigation of Chloride Salt Erosion on Asphalt Binders and Mixtures: Performance Evaluation and Correlation Analysis.
Materials (Basel)
January 2025
College of Engineering, Zhejiang Normal University, Jinhua 321004, China.
Asphalt pavement, widely utilized in transportation infrastructure due to its favourable properties, faces significant degradation from chloride salt erosion in coastal areas and winter deicing regions. In this study, two commonly used asphalt binders, 70# base asphalt and SBS (Styrene-Butadiene-Styrene)-modified asphalt, were utilized to study the chloride salt erosion effect on asphalt pavement by immersing materials in laboratory-prepared chloride salt solutions. The conventional properties and adhesion of asphalt were assessed using penetration, softening point, ductility, and pull-off tests, while Fourier transform infrared spectroscopy (FTIR) elucidated the erosion mechanism.
View Article and Find Full Text PDFQuantitative Measurement of Interfacial Adhesion of CVD Grown Bilayer WS on Various Substrates.
Small
December 2024
School of Mechanical and Materials Engineering, Indian Institute of Technology Mandi, Himachal Pradesh, 175075, India.
The interfacial adhesion between transition metal dichalcogenides (TMDs) and the growth substrate significantly influences the employment of flakes in various applications. Most previous studies have focused on MoS and graphene, particularly their interaction with SiO/Si substrates. In this work, the adhesion strength of CVD-grown bilayer WS is directly measured using the nano scratch technique on three different substrates-Sapphire, SiO/Si, and fused quartz.
View Article and Find Full Text PDFTitanate-polyurethane-chitosan ternary nanocomposite as an efficient coating for steel against corrosion.
Sci Rep
December 2024
Materials Science and Nanotechnology Department, Faculty of Postgraduate Studies for Advanced Sciences (PSAS), Beni-Suef University, Beni-Suef, 62511, Egypt.
In this study, a titanate-polyurethane-chitosan ternary nanocomposite was prepared by physical mixing. Sodium titanate nanotubes (Na-TNTs) were prepared by the hydrothermal method, and chitosan was extracted from shrimp shell. Na-TNTs were mixed with polyurethane (PU) of different ratios by weight, and chitosan was added after optimization.
View Article and Find Full Text PDFInfluence of Laser Micro-Texturing and Plasma Treatment on Adhesive Bonding Properties of WC-Co Carbides with Steel.
Materials (Basel)
December 2024
Department of Metal Forming, Welding and Metrology, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-370 Wrocław, Poland.
This article presents research on advanced surface preparation methods for sintered carbides (WC-Co, grade B2) commonly used in the tool industry, particularly in the context of bonding these materials with C45 steel using adhesives. Sintered carbides are widely used due to their high hardness, wear resistance, and good ductility, making them ideal for manufacturing tools operating in harsh conditions. Traditional bonding methods, such as brazing and welding, often result in stresses and cracks.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!