We describe the restorative treatment of an 86-year-old female patient who was referred to our specialist prosthodontics clinic. Due to secondary osteoporosis, she underwent oral antiresorptive therapy with ibandronic acid for 10 years. Although she was classified as a patient at increased risk of drug-induced osteonecrosis of the jaw, she eventually signed a consent form for fixed implant-supported prosthetic rehabilitation in her 4th sextant. However, after tooth extraction, the bone ridge was too small at the intended implant positions. Therefore, guided bone regeneration was performed with a computer-aided design/computer-aided manufacturing three-dimensional printed titanium mesh. Finally, a continuous augmented hard tissue ridge above 7 mm was found, and three implants were inserted. Eventually, after four months of submerged healing, the implants were loaded with single crowns. Now, the patient is seen regularly for supportive peri-implant therapy.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9617713 | PMC |
| http://dx.doi.org/10.1155/2022/5174075 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Evaluation of sticky bone in guided bone regeneration in the aesthetic area of the anterior teeth: a retrospective study.
Int J Oral Maxillofac Surg
January 2025
Stomatological Hospital of Chongqing Medical University, Chongqing, China; Chongqing Municipal Key Laboratory of Oral Biomedical Engineering of Higher Education, Chongqing, China; Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing, China. Electronic address:
The retrospective study aimed to compare the space-maintaining effects of sticky bone (bone graft matrix enriched with injectable platelet-rich fibrin) and titanium mesh for bone augmentation in the aesthetic zone. Patients who underwent single implant placement and had type 2/4 alveolar bone defects (buccal bone wall loss is >50% of the expected implant length) were screened for inclusion in this study. The labial bone plate width was measured at 1, 3, and 5 mm below the apical implant platform on cone beam computed tomography images taken immediately and 6 months after surgery.
View Article and Find Full Text PDFIntracranial Hypotension Mechanism and Implant Retention Procedure for Patients With Titanium Mesh Exposure.
Oper Neurosurg (Hagerstown)
January 2025
Department of Neurosurgery, Huashan Hospital, Shanghai Medical College, Fudan University, Shanghai, China.
Background And Objectives: The study aimed to investigate the potential pathogenesis and present an implant retention procedure for patients with titanium mesh exposure after cranioplasty.
Methods: The clinical data were obtained from 26 consecutive cases with titanium mesh exposure who underwent surgical treatment between 2018 and 2023. These patients' medical records, scalp photographs, operative notes, and outcomes were retrospectively analyzed.
3D-printed porous titanium versus polyetheretherketone cages in lateral lumbar interbody fusion: a systematic review and meta-analysis of subsidence.
Front Med (Lausanne)
December 2024
Department of Orthopedics, Tongren Hospital, Shanghai Jiao Tong University School of Medicine, Shanghai, China.
Article Synopsis
- Cage subsidence can negatively affect lumbar fusion procedures, with material selection (PEEK vs. 3D-Ti) influencing this issue; the study aims to compare their subsidence rates.
- The systematic search reviewed 265 patients from three high-quality studies, focusing on cage subsidence and classified subsidence rates using a specific method.
- Results indicated that 3D-Ti cages have a significantly lower rate of subsidence compared to PEEK cages, with less severe subsidence and better overall performance.
Impact of titanium mesh cage slotting width on anterior cervical corpectomy and fusion for compression cervical spondylosis with MRI T2WI hyperintensity: a one-year follow-up study.
J Orthop Surg Res
December 2024
Department of Orthopedics, Orthopedic Research Institute, West China Hospital, Sichuan University, Chengdu, 610041, Sichuan Province, China.
Background: Anterior cervical corpectomy and fusion (ACCF) is a standard surgical procedure for cervical spondylosis with spinal cord compression (CSWSCC), especially in patients with intensity on T2-weighted imaging high signal (T2WIHS). The titanium mesh cage (TMC) utilized in this procedure is essential in stabilizing the spine; however, the optimal slotting width of the TMC remains unclear.
Objective: This study aimed to investigate the impact of TMC slotting width on the clinical and radiological outcomes of ACCF in patients with spinal cord compression type cervical spondylosis with intensity on T2WIHS (CST2WIHS).
Surgical management of costal margin rupture associated with intercostal hernia: Evolution of techniques.
J Trauma Acute Care Surg
October 2024
From the Sheffield Teaching Hospitals NHS Foundation Trust (P.W., J.N.R., S.T., J.G.E.), Sheffield, England; Erasmus Medical Centre (M.M.E.W.), Rotterdam, The Netherlands; and University Hospital of Southampton NHS Foundation Trust (A.T.).
Introduction: Costal margin rupture (CMR) injuries in association with intercostal hernia (IH) are rare and symptomatic and provide a significant surgical challenge. Surgical failure rates up to 60% are reported, and optimal techniques are unclear. We have characterized these injuries and describe the evolution of our surgical management techniques.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!