Solar still is a cheap decentralized mode for obtaining potable water from saline water using solar energy, but it has low productivity. Previous studies showed that using pin fins in the absorber can increase the solar still efficiency and yield. The heat sink has better heat transfer properties than those of the pin fin because it has a higher surface area to volume ratio than that of the pin fin. The current study investigates the effect of heat sinks in passive pyramid solar still under two water depths (11 and 30 mm) on the hourly yield, accumulated yield, and efficiency of the distiller. Three cases were compared: conventional solar still (CSS), regular distribution of heat sinks (DHS), and grouped heat sinks in the middle of the solar still basin (GHS). In addition, the effect of atmospheric parameters such as solar radiation, UV index, humidity, dry bulb temperature, and ambient temperature on the solar still parameters such as water, vapor, cover, and feedwater temperature is investigated. Unexpectedly, heat sinks weakly affect the performance of solar still. Therefore, the conclusion of the previous studies that the finned absorber has a favorable impact on the solar still performance is not general and needs further investigation. The highest thermal efficiency was observed for the DHS and GHS at 30-mm water depth, where the efficiency was 35%.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1007/s11356-022-23779-y | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Highly Thermal-Conductive Cubic Boron Arsenide: Single-Crystal Growth, Properties, and Future Thin-Film Epitaxy.
J Phys Chem Lett
January 2025
College of Electronic and Optical Engineering & College of Flexible Electronics (Future Technology), State Key Laboratory of Organic Electronics and Information Displays, Nanjing University of Posts and Telecommunications, Nanjing, Jiangsu 210023, P.R. China.
Heat dissipation has become a critical challenge in modern electronics, driving the need for a revolution in thermal management strategies beyond traditional packaging materials, thermal interface materials, and heat sinks. Cubic boron arsenide (c-BAs) offers a promising solution, thanks to its combination of high thermal conductivity and high ambipolar mobility, making it highly suitable for applications in both electronic devices and thermal management. However, challenges remain, particularly in the large-scale synthesis of a high-quality material and the tuning of its physical properties.
View Article and Find Full Text PDFLow latency carbon budget analysis reveals a large decline of the land carbon sink in 2023.
Natl Sci Rev
December 2024
Laboratoire des Sciences du Climat et de l'Environnement, University Paris Saclay CEA CNRS, Gif sur Yvette 91191, France.
In 2023, the CO growth rate was 3.37 ± 0.11 ppm at Mauna Loa, which was 86% above that of the previous year and hit a record high since observations began in 1958, while global fossil fuel CO emissions only increased by 0.
View Article and Find Full Text PDFDominant atmospheric circulation patterns associated with the rapid intensification of summer flash droughts in Eastern China.
Sci Total Environ
December 2024
Key Laboratory of Hydrometeorological Disaster Mechanism and Warning of Ministry of Water Resources/Collaborative Innovation Center on Forecast and Evaluation of Meteorological Disasters, Nanjing University of Information Science and Technology, Nanjing 210044, China; School of Hydrology and Water Resources, Nanjing University of Information Science and Technology, Nanjing 210044, Jiangsu, China.
Flash droughts (FDs), which are characterized by rapid intensification, occurred frequently over Eastern China, posing great challenges for drought forecasting and preparation on subseasonal timescale. However, the drivers of the rapid development of FDs are not well understood. By comparing with slow droughts (SDs), this study investigates the dominant physical processes responsible for FDs in four different regions over Eastern China through diagnosing moisture budgets and further linking them to large-scale atmospheric circulation patterns.
View Article and Find Full Text PDFEnhancing EDM Productivity for Plastic Injection Mold Manufacturing: An Experimental Optimization Study.
Polymers (Basel)
October 2024
Department of Engineering and Technology Management, Faculty of Engineering, Northern University Centre of Baia Mare, Technical University of Cluj-Napoca, 62A Victor Babes Street, 430083 Baia Mare, Romania.
Electrical erosion molding (EDM) is an unconventional machining technology widely used in the manufacture of injection molds for plastics injection molding for the creation of complex cavities and geometries. However, EDM productivity can be challenging, directly influencing mold manufacturing time and cost. This work aims to improve EDM productivity in the context of mold manufacturing for plastics injection molding.
View Article and Find Full Text PDFA plateau freshwater shallow lake as a significant CO sink during the ice-covered period: A case study of Lake Wuliangsuhai, China.
Sci Total Environ
December 2024
Faculty of Biological and Environmental Sciences, Ecosystems and Environment Research Programme, Lammi Biological Station, University of Helsinki, Lammi FI-16900, Finland; Masinotek Oy, Ensimmäinen Savu 2, Vantaa FI-01510, Finland.
Lakes are essential for estimating the global CO budget. However, approximately 50 % of lakes undergo periodic freezing, and there is limited research on the factors influencing the CO cycle and ice formation in freshwater lakes located in middle- and high-latitude plateaus during ice-covered periods. Using high-frequency meteorological-flux data collected over six consecutive months during the 2018-2019 freezing period of Lake Wuliangsuhai, this study explored the diurnal variation, daily accumulation, and monthly accumulation of the CO cycle and its influencing mechanisms at a half-hour scale.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!