A gas path analysis approach of dynamic modelling was used to examine the gas turbine performance. This study presents an investigation of the effect of physical faults on the performance of a three-shaft gas turbine at full-load and part-load operation. A nonlinear steady state performance model was developed and validated. The datasheet from the engine manufacturer was used to gather the input and validation data. Some engineering judgement and optimization were used. Following validation of the engine performance model with the engine manufacturer data using physical fault and component health parameter relationships, physical faults were implanted into the performance model to evaluate the performance characteristics of the gas turbine at degradation state at full- and part-load operation. The impact of erosion and fouling on the gas turbine output parameters, component measurement parameters, and the impact of degraded components on another primary component of the engine have been investigated. The simulation results show that the deviation in the output parameters and component isentropic efficiency due to compressor fouling and erosion is linear with the load variation, but it is almost nonlinear for the downstream components. The results are discussed following the plots.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9573422 | PMC |
| http://dx.doi.org/10.3390/s22197150 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Determination of Vibration Properties and Reliable Frequency Estimation for Synchronous Vibrations Through Improved Blade Tip Timing Techniques Without a Once-per-Revolution Sensor.
Sensors (Basel)
January 2025
Institute of Power Plant Technology, Steam and Gas Turbines, RWTH Aachen University, 52062 Aachen, Germany.
Synchronous vibrations, which are caused by periodic excitations, can have a severe impact on the service life of impellers. Blade Tip Timing (BTT) is a promising technique for monitoring synchronous vibrations due to its non-intrusive nature and ability to monitor all blades at once. BTT generally employs a Once-per-Revolution (OPR) sensor that is mounted on the shaft for blade identification and deflection calculation.
View Article and Find Full Text PDFExperimental investigation of bluff body geometry effects on nitrogen oxides emissions from Cambridge stratified burner.
Sci Rep
January 2025
Department of Mechanical Engineering, Tarbiat Modares University, Tehran, Iran.
In this study, a series of experiments are done to analyze the effect of bluff body geometry on the NO reduction of a natural gas-air stratified swirl burner. The stratified burner of Cambridge University is chosen to study the mentioned geometrical effect, and the geometry modification of bluff body is used as a simple method for NO reduction, which can be easily applied to the systems using these burners, including gas turbines. The bluff body geometrical change to an annular bluff body is inspired by the fact that the areas in which the edge of the bluff body is in contact with the unburned flow have lower temperatures, which can drastically affect combustion parameters, especially emissions.
View Article and Find Full Text PDFAerodynamic performance enhancement of centrifugal compressor using numerical techniques.
F1000Res
January 2025
Department of Aeronautical & Automobile Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, Karnataka, 576104, India.
Background: Centrifugal compressors are dynamic machines utilizing a rotating impeller, efficiently accelerate incoming gases, transforming kinetic energy into pressure energy for compression. They serve a wide range of industries, including air conditioning, refrigeration, gas turbines, industrial processes, and applications such as air compression, gas transportation, and petrochemicals, demonstrating their versatility. Designing a centrifugal compressor poses challenges related to achieving high aerodynamic efficiency, surge and choke control, material selection, rotor dynamics, cavitation, erosion, and addressing environmental considerations while balancing costs.
View Article and Find Full Text PDFA two-stage deep learning-based hybrid model for daily wind speed forecasting.
Heliyon
January 2025
John von Neumann Faculty of Informatics, Obuda University, Budapest, Hungary.
Global adoption of wind energy continues to increase, while improving the efficiency of turbine settings requires reliable wind speed (WS) models. The latest models rely on artificial intelligence (AI) optimizations which constructs tests on a range of novel hybrid models to examine the reliability. Gradient Boosting (GB), Random Forest (RF), and Long Short-Term Memory (LSTM) are used in new combinations for data pre-processing.
View Article and Find Full Text PDFThe Effect of Absorbed Hydrogen on the Rotors of Steel Machining Products During Powerful Turbo Aggregate Repairs.
Materials (Basel)
December 2024
Department of Strength of the Materials and Structures in Hydrogen-Containing Environments, Karpenko Physico-Mechanical Institute, National Academy of Sciences of Ukraine, 5 Naukova Str., 79601 Lviv, Ukraine.
Rotor shafts are the most heavily loaded and accident-prone parts of powerful turbine generators, which are cooled using hydrogen. To eliminate damage sustained during operations, repair work was carried out, including the removal of defective parts, surfacing, and turning. This study tested the machinability of the rotor shaft using prototypes made from 38KhN3MFA steel.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!