Microplastics are a widespread environmental contaminant that raises serious concern for aquatic organisms. Hence, the present study was conducted to investigate the spatial and seasonal variation of microplastics, their characteristics, polymer types and the risk assessment caused by the microplastics in six sampling sites along the Thoothukudi region. The average microplastic abundance ranged from 32 ± 26 to 232 ± 229 items/kg and 54 ± 41 to 619 ± 377 items/l in sediment and surface water, respectively, and they exhibited a significant spatial difference among the sampling sites. The microplastic abundance also showed a significant difference among the seasons with the monsoon significantly recording the highest mean microplastic abundance in sediment (160 ± 130 items/kg) and surface water (454 ± 374 items/l). In sediment and surface water, fragment (sediment: 52.72%, surface water: 40.89%), 0.5-1 mm (sediment: 43.96%, surface water: 31.11%) and blue-coloured (sediment: 52.33%, surface water: 41.85%) microplastics were dominant with no significant difference both spatially and seasonally. Polyethylene, the dominant polymer, was observed in both the sediment and surface water, accounting for about 47.58% and 49.83%, respectively, and it showed no significant difference among the selected sites. This signifies that they are homogenously distributed along the coast and further suggests that these particles persisted in the sediment and surface water for a longer period of time. The results of the polymer hazard index show that the sediment (PHI = 1181.63) and surface water (PHI = 1018.66) were severely contaminated (hazard level V) with microplastic polymers such as PE, PP, PS, PET and PA. It was also found that the degree of the microplastic contamination in sediment (PLI = 3.57) and surface water (PLI = 3.84) was lower (hazard level I). The overall risk index (RI) for sediment (253.48) and surface water (444.74) falls under the higher risk category. From the correlation analysis, a significantly positive relationship was observed between microplastics in sediment and surface water based on each classification (abundance, shape, size, colour and polymer). This suggests that microplastics rejoin the water column from the sediment through resuspension, which occurs due to the circulation, tides and sedimentation rate. This might be the reason for the higher microplastic abundance in the surface water than in the sediment. As a result, proper management measures to reduce plastic waste disposal in the marine environment should be implemented to lessen the effects of microplastics on marine biota and on public health.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s10661-022-10468-z | DOI Listing |
Sci Rep
December 2024
School of architecture, Ocean and energy power engineering, Wuhan University of Technology, Wuhan, 430070, China.
During maritime operations, extreme events such as explosions, grounding, and seal failures can cause water ingress into lubricant compartments, forming oil-water emulsions that significantly affect the lubrication performance of ship stern bearings. Existing studies mainly focus on low water content, with limited exploration of the impact of high water content on lubrication performance. To address this gap, viscosity measurements of oil-water mixtures were conducted, and an emulsification viscosity equation applicable to varying water contents was derived.
View Article and Find Full Text PDFSci Rep
December 2024
Department of Pediatric Dentistry, Faculty of Dentistry, Damascus University, Damascus, Syrian Arab Republic.
This study aimed to evaluate the histological success of pulpotomy in primary molars using white mineral trioxide aggregate (WMTA) mixed with 2.25% sodium hypochlorite (NaOCl) gel and to evaluate in vitro its physical and chemical properties. The study had a clinical stage and an in-vitro stage.
View Article and Find Full Text PDFSci Rep
December 2024
Department of Physics, Sakarya University, Sakarya, Turkey.
Environmental problems have increased the need for sustainable agricultural practices that conserve water and energy. Carob, an eco-friendly crop with multiple health benefits, holds the potential for economic evaluation. This study investigates the carob molasses extraction process, focusing on the influence of temperature and water quantity on the diffusion coefficient.
View Article and Find Full Text PDFSci Rep
December 2024
Department of Nano-Chemical Engineering, Faculty of Advanced Technologies, Shiraz University, Shiraz, Iran.
MXene-based (nano)materials have recently emerged as promising solutions for antibiotic photodegradation from aquatic environments, yet they are limited by scalability, stability, and selectivity challenges in practical settings. We formulated FeO-SiO/MXene ternary nano-photocomposites via coupled wet impregnation and sonochemistry approach for optimised tetracycline (TC) removal (the second most used antibiotic worldwide) from water using response surface methodology-central composite design (RSM-CCD). The photocatalysts containing various loading of FeO/SiO (5-45 wt%) on the MXene with a range of calcination temperatures (300-600 °C) via RSM optimisation were synthesised, characterised regarding crystallinity properties, surface morphology, binding energy, and light absorption capability, and analysed for TC degradation efficiency.
View Article and Find Full Text PDFSci Rep
December 2024
School of Mechanical Engineering, Qilu University of Technology (Shandong Academy of Sciences), Jinan, 250353, China.
Microtextured microneedles are tiny needle-like structures with micron-scale microtextures, and the drugs stored in the microtextures can be released after entering the skin to achieve the effect of precise drug delivery. In this study, the skin substitution model of Ogden's hyperelastic model and the microneedle array and microtexture models with different geometrical parameters were selected to simulate and analyse the flow of the microtexture microneedle arrays penetrating the skin by the finite-element method, and the length of the microneedles was determined to be 200 μm, the width 160 μm, and the value of the gaps was determined to be 420 μm. A four-pronged cone was chosen as the shape of microneedles, and a rectangle was chosen as the shape of the drug-carrying microneedle.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!