Solid state nanopores are central structures for many applications. To date, much effort has been spent on controlled fabrication of single nanopores, while relatively little work has focused on large scale fabrication of arrays of nanopores. In this work we show wafer-scale fabrication of plasmonic nanopores in 50 nm thick silicon nitride membranes with one or two 30 nm gold films, using electron beam lithography with a negative resist or a new version of colloidal lithography. Both approaches offer good control of pore diameter (even below 100 nm) and with high yield (>90%) of intact membranes. Colloidal lithography has the advantage of parallel patterning without expensive equipment. Despite its serial nature, electron beam lithography provides high throughput and can make arbitrary array patterns. Importantly, both methods prevent metal from ending up on the membrane pore sidewalls. The new fabrication methods make it possible to compare the optical properties of structurally identical plasmonic nanopore arrays with either long-range order (e-beam) or short-range order (colloidal). The resonance features in the extinction spectrum are very similar for both structures when the pitch is the same as the characteristic spacing in the self-assembled colloidal pattern. Long-range ordering slightly enhances the magnitude of the extinction maximum and blueshift the transmission maximum by tens of nm. Upon reducing the diameter in long-range ordered arrays, the resonance is reduced in magnitude and the transmission maximum is further blue shifted, just like for short-range ordered arrays. These effects are well explained by interpreting the spectra as Fano interference between the grating-type excitation of propagating surface plasmons and the broad transmission individual pores in the metal film. Furthermore, we find that only the short-range ordered arrays scatter light, which we attribute to the highly limited effective period in the short-range ordered system and the corresponding lack of coherent suppression of scattering by interference effects.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9418017PMC
http://dx.doi.org/10.1039/c9na00585dDOI Listing

Publication Analysis

Top Keywords

electron beam
12
colloidal lithography
12
ordered arrays
12
short-range ordered
12
optical properties
8
plasmonic nanopore
8
nanopore arrays
8
nanopores work
8
beam lithography
8
transmission maximum
8

Similar Publications

Magnesium phosphate grains, minor accessory minerals found on the primitive meteorite Yamato 980115 (Y 980115), were investigated by Raman microspectroscopy. All magnesium phosphate grains found in the present study can be assigned to farringtonite, dehydrated magnesium phosphate Mg(PO)-I. Since the Mg(PO)-I is generally formed via the irreversible thermal transition from the polymorphs of Mg(PO)-II and -III at above 750-800 degree Celsius, we can infer that the parent body of the Y 980115 meteorites experienced thermal alteration with such a high temperature.

View Article and Find Full Text PDF

Transmission electron microscopy can be used for the characterisation of a wide range of thin specimens, but soft matter and aqueous samples such as gels, nanoparticle dispersions, and emulsions will dry out and collapse under the microscope vacuum, therefore losing information on their native state and ultimately limiting the understanding of the sample. This study examines commonly used techniques in transmission electron microscopy when applied to the characterisation of cryogenically frozen Pickering emulsion samples. Oil-in-water Pickering emulsions stabilised by 3 to 5 nm platinum nanoparticles were cryogenically frozen by plunge-freezing into liquid ethane to retain the native structure of the system without inducing crystallisation of the droplet oil cores.

View Article and Find Full Text PDF

Subnanometer Tracking of the Oxidation State on CoO Nanoparticles by Identical Location Imaging and Spectroscopy.

ACS Appl Mater Interfaces

January 2025

Department of Inorganic Chemistry, Fritz-Haber-Institut der Max-Planck-Gesellschaft, Berlin 14195, Germany.

Understanding a catalytic reaction requires tools that elucidate the structure of the catalyst surface and subsurface, ideally at atomic resolution and under reaction conditions. Operando electron microscopy meets this requirement in some cases, but fails in others where the required reaction conditions cannot be reached or lead to an unwanted influence of the electron beam on the reactant and catalyst. We introduce ILIAS (identical location imaging and spectroscopy) in combination with a quasi in situ approach to disentangle the effect of heat and gas on the surface of nanoparticles from the effect of the electron beam.

View Article and Find Full Text PDF

High-quality thin lamellae are essential for state-of-the-art scanning transmission electron microscopy (S/TEM) analyses. While the preparation of S/TEM lamellae using focused ion beam (FIB-) scanning electron microscopy (SEM) has been established since the early 21st century, two critical factors have only recently been addressed: precise control over lamella thickness and a systematic understanding of FIB-induced damage. This study conducts an experimental investigation and simulation to explore how the intensities of backscattered and secondary electrons (BSEs and SEs, respectively) depend on lamellae thickness for semiconductor (Si), insulator (Al2O3), and metallic (stainless-steel) materials.

View Article and Find Full Text PDF

Laser surface alloying of Fe, Si, and C on aluminium is demonstrated using a Q-switched Nd:YAG laser as the source of energy. The fundamental wavelength of the laser beam was 1064 nm with an output energy of 100 mJ and a pulse duration of 10 ns. The exposure was conducted in repetitive mode with a frequency rate of 1 Hz.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!